Results 101 to 110 of about 22,625 (269)
Advanced Engineering Materials, EarlyView.Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari +5 more
wiley +1 more source
Symmetry‐Guided Multifunctional Acoustic System Based on Mechanically Actuated Sonic Crystals
Advanced Engineering Materials, EarlyView.This study presents the design, simulation, and experimental validation of amultifunctional acoustic metamaterial based on rotationally engineered sonic crystals.By tuning cylinder orientations, controllable band gaps and six distinct functionalities—including switching, topological insulation, beam splitting, and logic operations—areachieved ...
Yuanyan Zhao +2 more
wiley +1 more source
THE INFLUENCE OF CHEMICAL COMPOSITION ON THE CORROSION RATE OF HIGH-CHROMIUM CAST IRON
Литьë и металлургия, 2017 The influence of the chemical composition on the corrosion rate of high-chromium cast iron was researched. During the castings’ cooling process the replacement of the atoms of nickel, iron and manganese by the atoms of chromium in the carbides took place.
V. V. Netrebko, I. P. Volchok
doaj
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Long - range foundry Al composite alloys
Metalurgija, 2014 The technology of obtaining nanostructural composite aluminum alloys consists in the plasma injection of refractory nanometric particles with simultaneous two-plane magnetic dynamic mixing of the melt.
A. D. Mekhtiev +4 more
doaj
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran +6 more
wiley +1 more source
Mechanistic modulation of electronic structure and interface chemistry in Ni-based alloys for electrochemical energy conversion. [PDF]
RSC AdvAli Umar A, Oyama M.
europepmc +1 more source