Results 241 to 250 of about 136,476 (299)

Development of micro dual temperature-heat flux sensing probe using Pt Thin film for transient heat measurements up to 1400 °C. [PDF]

Microsyst Nanoeng
Wang H, Kong M, Wang H, Zhang F, Yang Z, Hao T, Yang J, Xu R, Zhan Y, Liang J, Liu Z.   +10 more
europepmc   +1 more source

Mechanical and adhesive properties of monolithic zirconia and their clinical implications: a narrative review. [PDF]

Saudi Dent J
Abdulgader AA.
europepmc   +1 more source

The novel alumina/CQDs nanocomposites for modifying optical and structural properties of alumina nanostructure. [PDF]

Sci Rep
Gholizadeh Z, Aliannezhadi M, Ghominejad M, Shariatmadar Tehrani F.   +3 more
europepmc   +1 more source

Enhanced Properties of Alumina Cement Adhesive for Large-Tonnage Insulator Under Rapid Curing Regime. [PDF]

Materials (Basel)
Zhou W, Min Y, Zhou J, Tian S.
europepmc   +1 more source

Bridging classical and quantum interpretation of chemical state analysis by XPS/HAXPES to resolve short-range order in amorphous alumina films.

J Mater Chem A Mater
Gramatte S, Wang X, Hernández Bertrán MA, Cancellieri C, Pizzi G, Prezzi D, Timrov I, Politano O, Utke I, Jeurgens LPH, Turlo V.   +10 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Alumina Biocompatibility

Journal of Long-Term Effects of Medical Implants, 2018
Alumina (Al2O3) ceramic is widely used for medical devices and its biocompatibility is well known and is reported in articles and textbooks. However, finding proof of this assertion gathered over more than 40 years can be challenging. We performed a literature review about alumina biocompatibility to compile data from the literature.
Eric, Denes, Guislaine, Barrière, Evelyne, Poli, Guillaume, Lévêque   +3 more
openaire   +2 more sources

Hydraulic Alumina Binder for Extrusion of Alumina Ceramics

Journal of the American Ceramic Society, 2007
The present work describes the effect of hydraulic alumina (HA) as a new inorganic binder on extrusion of alumina ceramics. The addition of a small amount of HA imparted significant flowability and rigidity to the extruded alumina.
Takaaki Nagaoka, Cihangir Duran, Toshihiro Isobe, Yuji Hotta, Koji Watari   +4 more
openaire   +2 more sources

Engineering aspect of alumina on alumina hip prosthesis

Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine, 2007
Alumina on the alumina sliding system in a total hip replacement is recognized as a breakthrough in orthopaedic surgery. Advantages and problems with this material are explained and discussed in the light of 36 years of clinical application. Laboratory data as well as clinical ones are summarized.
L, Sedel, A, Raould
openaire   +2 more sources

Alumina-on-alumina hip implants

The Journal of Bone and Joint Surgery. British volume, 2012
Alumina–alumina bearings are among the most resistant to wear in total hip replacement. Examination of their surfaces is one way of comparing damage caused by wear of hip joints simulated in vitro to that seen in explanted bearings. The aim of this study was to determine whether second-generation ceramic bearings exhibited a better pattern of wear than
Affatato, S, Traina, F, De Fine, M, Carmignato, S, Toni, A   +4 more
openaire   +3 more sources