Results 51 to 60 of about 136,222 (300)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source

IMPROVEMENT OF WORKABILITY OF PORCELAIN UNDER EFFECT OF ALUMINA

Diyala Journal of Engineering Sciences, 2012
Adding of alumina to porcelain improve the mechanical properties of the green and fired body.         This improvement depend on the properties of the added alumina, such as surface area, morphology and the percentage of the alumina.
Jaleel I.k.Al.Robayie
doaj   +1 more source

Processing and characterization of monoclinic-zirconia fibre-matrix interfaces in dense matrix alumina-alumina composites: Processamento e caracterização de interfaces fibra-matriz de zircônia não estabilizada em compósitos alumina-alumina de matriz densa [PDF]

, 2013
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Engenharia Mecânica, Florianópolis, 2013.Interfaces fibra-matriz tem um papel muito importante no desempenho de compósitos de matriz ...
Blaese, Diego
core  

Dielectric breakdown of alumina thin films produced by pulsed direct current magnetron sputtering [PDF]

, 2018
Alumina films (~2 μm thick) were deposited with a mixed Cu/Al interlayer onto copper. Direct current (DC)/Pulsed DC (PDC) magnetron sputtering techniques were independently compared for reactive alumina sputtering.
Hanby, Benjamin V.T., Moffat, Jonathan, Grant, Colin, Grant, David M., Blissett, Jonathan, Gerada, Chris, Gimeno-Fabra, Miquel, Stuart, Bryan W.   +7 more
core   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Alumina Powder Properties Obtained by Neutralization Process of Sodium Aluminate

The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2009
Today, the most production of alumina is used for aluminum production [1, 2] (metallurgy alumina), minor production of alumina is used for special purpose, as fire-resistant materials, electro porcelain and etc., and because this alumina are called ...
Mitar PERUŠIC, Vladan MIĆIĆ, Zoran OBRENOVIĆ, Radislav FILIPOVIĆ   +3 more
doaj  

Produção de compósitos de matriz cerâmica de alumina a partir de colagem de fitas em meio aquoso [PDF]

, 2012
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Ciência e Engenharia de Materiais, Florianópolis, 2012Compósitos de matriz cerâmica têm sido desenvolvidos para superar a fragilidade ...
Amadio, Tatiane de Mattos
core  

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Recent Advances in the Processing and Properties of Alumina–CNT/SiC Nanocomposites

Nanomaterials, 2019
An alumina-based nanocomposite is fabricated through the addition of secondary nanophase material to an alumina matrix to alter and tailor the properties of alumina. The addition to alumina of semi-conductive materials, such as silicon carbide (SiC), and
Ibrahim Momohjimoh, Mohamed A. Hussein, Nasser Al-Aqeeli   +2 more
doaj   +1 more source