Results 151 to 160 of about 1,088,927 (341)

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam

Advanced Engineering Materials, EarlyView.
Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley   +1 more source

Impact of Pre‐Oxidation Treatments on a Recycled MgO/Steel‐Composite as Carbon Free Anode in Aluminum‐Electrolysis Environments

Advanced Engineering Materials, EarlyView.
Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser, Felix Drechsler, Nora Brachhold, Florian Kerber, Christos G. Aneziris   +4 more
wiley   +1 more source

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

Advanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb, Zachary T. Kloenne, Samuel R. Rogers, Chi Hang Dominik Kwok, Mark C. Hardy, Michele S. Conroy, David Dye   +6 more
wiley   +1 more source

Transient Lightning Response of a New Substation Grounding Method Using General FEM Software

Applied Sciences
This paper presents a numerical investigation studying the response of a new grounding system when submitted to different lightning current waveforms. This grounding system features an electrically conductive concrete (ECON) or geopolymer (ECG) square ...
Alhassane Sylla, Christophe Volat, Reza Jafari Aminabadi, Guy Simard   +3 more
doaj   +1 more source

Sintered aluminium heat pipe (SAHP) [PDF]

, 2012
This work is the product of an ongoing PhD project in the School of the Built and Natural Environment of Northumbria University in collaboration with the University of Liverpool and Thermacore Europe Ltd. The achievements at the end of the first year are
Agnew, Brian, Ameli, Masoud, McGlen, R. J., Ng, Bobo, Singh, J., Sutcliffe, C. J.   +5 more
core  

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process

Advanced Engineering Materials, EarlyView.
This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima, Christian Schimpf, Stefan Martin, Olga Fabrichnaya, David Rafaja   +4 more
wiley   +1 more source