Results 71 to 80 of about 40,640 (288)
A study on surface cracking in extrusion of aluminium alloy AA2014
, 2004 Surface cracking is generally recognised as one of the main defects occurring during the process of aluminium extrusion, especially in the case of the so called hard aluminium alloys.
Sheppard, Terry, Peng, Z.
core +1 more source
The Influence of the Structure on the Fatigue Properties of Al-Mg Cast Alloy
Archives of Metallurgy and Materials, 2017 The article will be focused on monitoring the influence of the structure on the fatigue properties of aluminium alloys for the casting of type Al-Mg. As an experimental material were used aluminium alloys EN AC 51200 and EN AC 51500, supplied in a cast ...
Uhríčik M. +4 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Development of a super ductile diecast Al-Mg-Si alloy [PDF]
, 2012 This is the post-print version of the final paper published in Materials Science and Engineering A. The published article is available from the link below.
Watson, D, White, M, Fan, Z
core +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Grain refinement and nucleation processes in Aluminium alloys through liquid shearing
, 2009 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The industrial practice of grain refinement of aluminium alloys involves the addition of inoculant particles to initiate alpha-aluminium grains at small ...
Haghayeghi, Reza
core
Fatigue crack growth behaviour and life prediction for 2324-T39 and 7050-T7451 aluminium alloys under truncated load spectra [PDF]
, 2010 This paper presents a study of crack growth behaviour in aluminium alloys 2324- T39 and 7050-T7451 subjected to flight-by-flight load spectra at different low- stress truncation levels. Crack branching was observed in the higher truncation levels for the
Bao, Rui, Zhang, Xiang
core +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Grain refinement efficiency of a new oxide-containing master alloy for aluminium casting alloys [PDF]
, 2014 In this study, grain refinement efficiency of a new oxide master alloy based on MgAl2O4 was demonstrated on an A357 alloy. The grain size of the reference alloy was reduced by 50-60% with the addition of the master alloy and introduction of ultrasonic ...
Dmitry G. Eskin +7 more
core +1 more source
MetalsAluminium alloys have a wide range of applications, mainly due to their advantageous strength-to-weight ratio, denoted as specific strength and corrosion resistance.
Martin Mikolajčík +5 more
doaj +1 more source