Results 91 to 100 of about 347,352 (352)

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

Novel Tailoring of Ternary ZnS‐MXene‐TiO2 Nanocomposite Heterojunction and Its Tunable Electrochemical Properties With Enhanced Photocatalytic Degradation

Advanced Engineering Materials, EarlyView.
ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir, Dohyun Kim, Minho Song, Jae Doc Na, Young Jun Joo, Kwang Youn Cho, Karna Wijaya, Won‐Chun Oh   +7 more
wiley   +1 more source

Cast composite products with aluminium matrix

Izvestiya MGTU MAMI, 2014
The article considers the reinforcing elements from matrices of aluminum alloys. It presents data on the production technology of gradient-reinforced products. The technology of reinforcement and properties of castings with given content of ceramic filler is considered.
A. A. Pechnikov, A. Toleshuli, E. G Meshcheryakov   +2 more
openaire   +1 more source

Synergistic effects of zinc borate and aluminiumtrihydroxide on flammability behaviour of aerospaceepoxy system [PDF]

, 2009
The flame retardancy of mono-component epoxy resin (RTM6), widely used for aerospace composites, treated with zinc borate (ZB), aluminium trihydroxide (ATH) and their mixtures at different concentrations have been investigated by morphological and ...
Camino, Giovanni, De Fenzo, A., Formicola, C., Frache, Alberto, Giordano, M., Zarrelli, M.   +5 more
core   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Studies on Aluminum–Fly-Ash Composite Produced by Impeller Mixing [PDF]

, 2009
Metal matrix composites (MMCs) constitute an important class of design and weight-efficient structural materials that are encouraging every sphere of engineering applications. There has been an increasing interest in composites containing low density and
Tripathy, Shuvendu
core  

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Processing of advanced Al/SiC particulate metal matrix composites under intensive shearing – A novel rheo process [PDF]

, 2008
Particulate Metal Matrix Composites (PMMCs) have attracted interest for application in numerous fields. The current processing methods often produce agglomerated particles in the ductile matrix and as a result these composites exhibit extremely low ...
Barekar, NS, Dhindaw, BK, Fan, Z, Hari Babu, N, Patel, J, Tzamtzis, S   +5 more
core  

Creep fatigue life assessment of a pipe intersection with dissimilar material joint by linear matching method [PDF]

, 2016
As the energy demand increases the power industry has to enhance both efficiency and environmental sustainability of power plants by increasing the operating temperature.
Barbera, Daniele, Chen, Hao Feng, Liu, Ying Hua   +2 more
core   +1 more source

On the Machinability of an Al-63%SiC Metal Matrix Composite [PDF]

, 2020
This paper presents a preliminary study of aluminium matrix composite materials during machining, with a special focus on their behavior under conventional processes.
Batista Ponce, Moisés, Fernández Vidal, Severo Raúl, Mayuet Ares, Pedro Francisco, Repeto García, David, Salguero Gómez, Jorge   +4 more
core   +1 more source