Results 191 to 200 of about 92,878 (265)

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Thermal Conductivity in Nanoporous Aerogels: A Critical Review of Gas and Solid Conduction Models and Structure-Property Relations. [PDF]

Gels
Ramesh R, Barisik M.
europepmc   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source

Heteroepitaxial 3C-SiC for MEMS Applications. [PDF]

Micromachines (Basel)
Garofalo A, Muoio A, Belsito L, Sapienza S, Ferri M, Roncaglia A, La Via F.   +6 more
europepmc   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Multimodal machine learning for integrating heterogeneous analytical systems. [PDF]

Anal Sci
Muroga S, Nakajima H, Shimizu T, Kobashi K, Hata K.   +4 more
europepmc   +1 more source

Monte Carlo validation of signal-to-noise improvements in transmission imaging using correlated annihilation photon pairs. [PDF]

Sci Rep
Romanchek G, Yu Z, Abbaszadeh S.
europepmc   +1 more source

Predictions of Crack Growth Rates, R-Ratio and Overload Effects Based on Smooth Specimen LCF Data and the Moving Plastic Stress Field Ahead of the Crack Tip. [PDF]

Materials (Basel)
Williams S, Whittaker M, Hardy M.
europepmc   +1 more source

Influence of Cutting-Edge Micro-Geometry on Material Separation and Minimum Cutting Thickness in the Turning of 304 Stainless Steel. [PDF]

Materials (Basel)
Zou Z, Xin Y, Ma C.
europepmc   +1 more source