Results 41 to 50 of about 2,071 (285)

Does Long‐Term Lower Extremity Strength Training in Adults With Knee Osteoarthritis and Varus Alignment Reduce Knee Joint Loading During Gait?

Arthritis Care &Research, EarlyView.
Objective We examined whether 18 months of strength training in individuals with knee varus alignment and medial tibiofemoral osteoarthritis (OA) reduced knee joint loads during walking compared to an attention control group. Methods This study was a secondary analysis of a randomized clinical trial that compared the effects of strength training to a ...
Stephen P. Messier, Matthew N. Vigliotti, Paige E. Rice, Brian Pietrosimone, Shannon L. Mihalko, Edward H. Ip, Richard F. Loeser, David J. Hunter, Ali Guermazi, Ryan Hill, Santiago Saldana, Kim L. Bennell, Paul DeVita   +12 more
wiley   +1 more source

Study on Simplified Model and Numerical Solution of High-Speed Angular Contact Ball Bearing

Shock and Vibration, 2020
For the calculation model of high-speed angular contact bearing has many variables, the large root difference exists, and the Newton iterative method solving the convergence depends on the initial value problems; thus, the simplified calculation model is
Guang Zeng, Chunjiang Zhao, Xiaokai Yu, Biao Sun, Zhigang Xiao, Qiang Bian, Bingyang Liu   +6 more
doaj   +1 more source

Fatigue Life Analysis of Ball Bearings and a Shaft System Considering the Combined Bearing Preload and Angular Misalignment

Applied Sciences, 2020
Bearing preload significantly affects the running performance of a shaft-bearing system including the fatigue life, wear, and stiffness. Due to the mounting error, the bearing rings are often angularly misaligned.
Yu Zhang, Mengqi Zhang, Yawen Wang, Liyang Xie   +3 more
doaj   +1 more source

Triangular Index Ratio as an Alternative Method to the Alpha Angle for Defining the Presence of Cam Morphology: A Prospective Cohort Study

Arthritis Care &Research, EarlyView.
Objective Cam morphology, which is a significant risk factor for hip osteoarthritis, is commonly quantified by the alpha angle (AA). This study aims to explore the potential of the triangular index ratio (TIR) to quantify cam morphology on anteroposterior radiographs by assessing the association between TIR‐defined cam morphology and the development of
Jinchi Tang, Fleur Boel, Michiel M. A. van Buuren, Noortje S. Riedstra, Myrthe A. van den Berg, Jos Runhaar, Sita Bierma‐Zeinstra, Rintje Agricola   +7 more
wiley   +1 more source

Dynamic Service Mechanism of Double-Row Spherical Roller Bearings Due to Self-Aligning Behavior

Machines, 2023
Spherical roller bearings (SRBs) are widely used under self-aligning operating conditions, such as rotor bending or an angular misalignment between inner and outer rings due to their self-aligning function.
Yu Xing, Yifei Zhang, Yin Zhang, Daoyun Qiao, Yuxia Pei, Yuan Xiao   +5 more
doaj   +1 more source

Pain and Patient‐Reported Physical Function Did Not Differ Among Body Composition Profiles in Patients With Hip Osteoarthritis

Arthritis Care &Research, EarlyView.
Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan, Boliang Wang, Fiona Dobson, Ben Kirk, Travis Haber, Kim L. Bennell, Shirley P. Yu, Kim Allison, Ricardo J. S. Costa, Gabrielle Knox, Michelle Hall   +10 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

The Influence of Preload on the Work of Angular Contact Ball Bearings [PDF]

Archive of Mechanical Engineering, 2016
Abstract Optimum values of preload can be achieved in well-tried constructions and then applied in similar structures. For new structures, it is recommended to calculate the preload force and to test the correctness of calculation by means of experiments. In practice it may be necessary to introduce corrections, because not all real work parameters can
Kaczor Jarosław, Raczyński Andrzej
openaire   +2 more sources

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Karl Popper and the Mechanisms of Hydrogen Embrittlement

Advanced Engineering Materials, EarlyView.
Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley   +1 more source