Results 141 to 150 of about 3,274,537 (356)
Advanced Engineering Materials, EarlyView.This study investigates the mechanical properties of Carbon/Aramid intraply hybrid fiber‐reinforced Elium composites under 6 months of water aging. After aging, flexural strength decreases by 25.89%, tensile strength by 4.40%, and fracture toughness by 21.56%.
Muhammed Huseyin Guzel, Gurol Onal
wiley +1 more source
The Effects of Grease Filling Amount on Temperature Performance of High-Speed Sealed Angular-Contact Ball Bearings [PDF]
, 2016 Jiafan Xue +2 more
openalex +1 more source
3D‐Printed Architected Material for the Generation of Foam‐Based Protective Equipment
Advanced Engineering Materials, EarlyView.This study investigates 3D‐printed architected structures as alternatives to traditional foams in protective gear. It focuses on customizing impact strength and damping through design and manufacturing integration. Testing shows these structures outperform conventional foams, offering enhanced customizability, lower weight, and tunable performance ...
Ali Zolfagharian +5 more
wiley +1 more source
Effect of the Angular Position of the Section of a Ring Cowling on the High Speed of an XF7C-1 Airplane [PDF]
The tests herein reported were conducted by the NACA to determine the effect of the angular position of the section of a ring cowling on the speed of an airplane having a radial air-cooled ...
Gough, Melvin N
core +1 more source
Advanced Engineering Materials, EarlyView.Periodic submicron features are fabricated on 304 stainless steel using single and double femtosecond laser pulses. By adjusting polarization, fluence, and inter‐pulse delay, 1D and 2D nanostructures are formed. Enhanced hydrophobicity and dense surface‐enhanced Raman spectroscopy hotspots enable analyte detection down to 10−10 M with good ...
Balaji Baskar +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk +4 more
wiley +1 more source
Additive Manufacturing of Highly Alloyed Aluminum–Lithium
Advanced Engineering Materials, EarlyView.Al–Li alloys, promising for future lightweight constructions due to their low density and high stiffness, are limited to 9 at% lithium in commercial forms because of segregation issues. To overcome this traditional limitation, powder bed fusion with an ultrashort pulse laser is used.
Lisa Matthäus +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Multilayering of TiN film with metallic Ti film is adopted to enhance the fracture resistance of TiN thin films. Plastic dissipation within Ti with process zone size of ≈250 nm, along with elastic–plastic mismatch driven changes to crack driving force enhances the crack growth resistance by ten times, enabling physics informed design of optimized ...
Nidhin George Mathews +5 more
wiley +1 more source
A Finite Element Method for Incompressible Fluid Flow in a Noninertial Frame of Reference and a Numerical Study of Circular Couette Flow with Varying Angular Speed [PDF]
, 2017 C. S. Jog, Nilesh Potghan
openalex +1 more source
Advanced Engineering Materials, EarlyView.Ni‐base superalloys produced using additive manufacturing (AM) have a different response to heat treatments when compared to their conventional counterparts. Due to such unpredictability, various alloys with industrial interest are currently overlooked in most prior AM research.
Guilherme Maziero Volpato +6 more
wiley +1 more source