Results 21 to 30 of about 17,188 (197)

Application of “high-fidelity and high-resolution” processing technology in thin reservoir identification: A case study of the deep Permian Maokou Formation in Penglai area, central Sichuan [PDF]

Youqicang pingjia yu kaifa
The deep Permian Maokou Formation in the Penglai area, central Sichuan, is located in the Sichuan Basin. It is a sedimentary formation primarily composed of carbonate rocks, with dolomite being the main lithology.
PENG Haotian, HE Qinglin, CHEN Kang, ZENG Ming, HE Zongqiang, TU Zhihui, KONG Lingxia, QU Bozhang
doaj   +3 more sources

Using fluorescence fluctuation spectroscopy to quantify molecular dynamics within cells

FEBS Open Bio, EarlyView.
Microscopy techniques like fluorescence correlation spectroscopy (FCS) and number and brightness analysis (N&B) allow to quantify concentrations, diffusion rates, and oligomerization of fluorescently labeled molecules in the living cell. In this protocol the principles of how to set up these types of experiments are described including calibration ...
Mark A. Hink
wiley   +1 more source

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

Advanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares, Nadège Bouchonneau, Christian Jochum, Donald Radford   +3 more
wiley   +1 more source

Flexural Behavior of 3D‐Printed Porous Bouligand‐Structured Polymers: Influence of Pitch Angle and Porosity

Advanced Engineering Materials, EarlyView.
This study examines how helicoidal architectures with different porosities respond to bending. Adjusting layer angle and spacing in 3D‐printed polymers reveals clear tradeoffs between stiffness, strength, and energy absorption. Experiments and simulations highlight designs that distribute stress effectively, offering pathways for optimizing lightweight
Praveenkumar Subhash Patil, Edward D. McCarthy, Parvez Alam   +2 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Self‐Sintering Ionogel Binder for Flexible, Recyclable, and Healable Printed Giant Magnetoresistive Sensors

Advanced Functional Materials, EarlyView.
ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo, Xiaotao Wang, Guannan Mu, Proloy Taran Das, Igor Veremchuk, Conrad Schubert, Aaron D. Cross, Yevhen Zabila, Xuan Peng, Larysa Baraban, Denys Makarov   +10 more
wiley   +1 more source

Advances in Sustainable and Wearable Textile Based Soft Robotics

Advanced Functional Materials, EarlyView.
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas, Marzia Dulal, Sophia K. Novoselov, Victoria K. Novoselov, Kostya S. Novoselov, Shaila Afroj, Nazmul Karim   +6 more
wiley   +1 more source

A monotone nonlinear cell-centered finite element method for anisotropic diffusion problems

Electronic Journal of Differential Equations, 2019
We present a technique to correct the cell-centered finite element scheme [20] (FECC) for full anisotropic diffusion problems on general meshes, which provides a discrete maximum principle (DMP).
Nguyen Anh Dao, Duc Cam Hai Vo, Thanh Hai Ong   +2 more
doaj  

Multimodal Optoelectronic Synapses for Neuromorphic Intelligence: Coupling Light, Electrical, Thermal, and Beyond

Advanced Functional Materials, EarlyView.
This review revisits optoelectronic neuromorphic devices that extend from unimodal sensing toward multimodal perception. Five types of stimuli‐to‐output information flow that are classified based on the device roles within the system and applications are summarized and discussed.
Jihyun Shin, Junhyung Cho, Wangmyung Choi, Jaehyun Hur, Jae Kyeong Jeong, Ulrike Kraft, Hocheon Yoo   +6 more
wiley   +1 more source

Stable Multipoint Flux Approximation (MPFA) scheme for anisotropic porous media

Alexandria Engineering Journal
This paper focuses on enhancing the multipoint flux approximation (MPFA) method for subsurface reservoir simulation with heterogeneous anisotropic permeability with discontinuities at grid block level.
Pijus Makauskas, Pal Mayur
doaj   +1 more source