Results 21 to 30 of about 5,598 (255)
Thick anodic oxide films were produced on aluminium using the sulphuric acid hard anodizing process. Low acid concentrations, low temperatures, high current densities and short processing times minimised oxide dissolution and gave the least porosity ...
Cunningham, Paul J.
core +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
, 2023 Aluminium 6061 merupakan paduan Al-Mg-Si bersifat ringan, mampu tempa, dan tahan korosi. Aluminium 6061 biasa digunakan untuk keperluan rumah tangga, pesawat terbang, suku cadang mobil, dll. Anodizing adalah metode pelapisan dengan cara membentuk lapisan
Syah, Alifah
core
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
, 2003 Anodizing is a versatile method used to prevent a metal from corrosion by forming an oxide coating over its surface. Various power supplies such as D.C.,A.C. and A.C. superimposed on D.C.
Vincent, S. +9 more
core +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Anodizing of Hydrogenated Titanium and Zirconium Films [PDF]
, 2021 Magnetron-sputtered thin films of titanium and zirconium, with a thickness of 150 nm, were hydrogenated at atmospheric pressure and a temperature of 703 K, then anodized in boric, oxalic, and tartaric acid aqueous solutions, in potentiostatic ...
Pligovka A +8 more
core +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Anodizing of aluminium parts for automotive applications [PDF]
, 2023 Tässä kandidaatintyössä perehdytään alumiinin pintakäsittelymenetelmään anodisointiin sekä anodisoinnin sovelluksiin ajoneuvokäytössä. Tutkimus avaa alumiiniseosten vaikutusta anodisointiprosessiin sekä oksidikalvon muodostumiseen.
Annola, Juho
core
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source