Results 71 to 80 of about 14,061 (304)
Advanced Engineering Materials, EarlyView.Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz +6 more
wiley +1 more source
Jurnal Energi Dan Manufaktur, 2012 To increase assess aluminium of decorative aspect hence finishing processes must be used, like coloringprocess. Hence layer anodizing developed now where you can make aluminum metal look more interesting so thefinish can increase the economic value ...
I Gst. Ngr. Nitya Santhiarsa
doaj
Influence of the anodizing process variables on the acidic properties of anodic alumina films [PDF]
, 2017 In the present work, the effect of the different variables involved in the process of aluminum anodizing on the total surface acidity of the samples obtained was studied.
Boldrini, Diego Emmanuel +2 more
core +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source
International Journal of Electrochemical Science, 2017 Titanium sheets are anodized to prepare titanium dioxide nanotubes (TiO2 NTs) with varying chemical polishing times, anodizing voltages, anodizing times and NH4F electrolyte concentrations. The surface morphology of the TiO2 NTs is observed by a Scanning
Shenghan Zhang +3 more
doaj +1 more source
Deterministic Detection of Single Ion Implantation
Advanced Engineering Materials, EarlyView.Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead +6 more
wiley +1 more source
Investigation of the Scanning Microarc Oxidation Process [PDF]
, 2017 Scanning microarc oxidation (SMAO) is a coating process which is based on conventional microarc oxidation (MAO). The key difference is that deposition in SMAO is achieved by using a stainless steel nozzle to spray an electrolyte stream on the substrate ...
Domblesky, Joseph P. +4 more
core +3 more sources
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
THE INFLUENCE OF SULFURIC ACID ANODIZING ELECTROCHEMICAL PROCESS ON SURFACE TREATMENT ADHESION
Nonconventional Technologies Review, 2019 This paper presents the influence of sulphuric acid anodizing electrochemical process on surface treatment adhesion, by testing two distinct scenarios. The paper presents the general context in the aerospace industry related to product service life, as ...
Vlad Ciprian Cupsan +2 more
doaj
Advances in Condensed Matter Physics, 2015 Nanoporous tin oxide layers were obtained on various Sn substrates including high- and low-purity foils and wire by one-step anodic oxidation carried out in a 0.3 M oxalic acid electrolyte at various anodizing potentials.
Leszek Zaraska +2 more
doaj +1 more source