Results 51 to 60 of about 7,735 (222)
Modelling and Analysis of Civil Structures in ANSYS Workbench Environment
, 2012 This thesis deals with the use of the ANSYS Workbench software environment for modelling and analysing of civil structures. The introductory part is focused on finite element method, which is used by the ANSYS environment.
Krňávek, Ondřej
core +1 more source
Diyala Journal of Engineering Sciences, 2022 In this study, the finite element method using ANSYS workbench 16.1 has been successfully used to predict the fatigue life, fatigue strength, and the factors of safety for the as cast AA5052 as arrow matrix and its composites: AA5052/7 wt% ZrO2, AA5052 ...
Baqir Ibraheem +2 more
doaj +1 more source
Journal of Prosthodontics, EarlyView.Abstract Purpose The present study aimed to evaluate, in a preclinical setting, the biomechanical behavior and mechanical performance of a newly developed dental implant nut system designed to address primary stability challenges in the severely resorbed posterior maxilla.
Mert Şahin +4 more
wiley +1 more source
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 7, Page 2892-2907, July 2026.ABSTRACT Characterization of the crack tip, such as the stress intensity factor (SIF), is a vital step for the assessment of fatigue crack growth and prediction of potential failure in engineering structures. This study investigates the use of thermoelastic stress analysis (TSA) for SIF evaluation, including a methodology for non‐adiabatic stress field
John Codrington +3 more
wiley +1 more source
The analysis of bearing capacity of main pipeline in presence of corrosion defects [PDF]
Омский научный вестник, 2019 A mathematical model is presented that allows modeling fatigue defects of corrosion origin on main pipelines. A method for assessing the crack resistance of the main pipeline wall with a corrosion defect is proposed.
К. А. Vansovich +3 more
doaj +1 more source
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Deep tillage tool optimization by means of finite element method: Case study for a subsoiler tine [PDF]
, 2010 Technologies and computer capacity currently available allow us to employ design software and numerical methods to solve complicated problems in very wide disciplines of engineering. It is also important for researches in agriculture.
Akinci, Ibrahim +5 more
core
Prototype Multifunctional Device for Contraction Exercises of Joints and Muscles of the Lower Limb [PDF]
Transactions of the VŠB-Technical University of Ostrava, Mechanical Series, 2013 In the article Authors are showing the endurance test of the prototype multifunctional device for contraction exercises of joints and strengthening muscles.
Pawel JURECZKO +3 more
doaj +1 more source
Health Science Reports, Volume 9, Issue 6, June 2026.ABSTRACT Background and Aims Little information is available on tooth displacement and periodontal ligament (PDL) stress distribution caused by computer assisted design‐computer assisted manufacturing (CAD/CAM) retainers. Therefore, the purpose of this study was to compare CAD/CAM and multistrand retainers in terms of PDL stresses, risk of root ...
Hanie Daryanavard +6 more
wiley +1 more source
Modal analysis of 4-cylinder engine crankshaft based on ANSYS Workbench
Journal of Measurement Science and Instrumentation, 2015 CATIA V5R20 software was utilized to build up a three-dimensional solid model of inline four-cylinder gasoline engine crankshaft.The free modal analysis of the first six orders from the whole crankshaft model was carried out based on TGrid algorithm by ...
LI Xue-min, CUI Zhi-qin
doaj