Results 51 to 60 of about 1,024 (167)
Guide for recommended practices to perform crack tip opening displacement tests in high strength low alloy steels [PDF]
Fracture mechanics approach is important for all mechanical and civil projects that might involve cracks in metallic materials, and especially for those using welding as a structural joining process.
Lima, Vinicius +4 more
core +4 more sources
Crack control technology for the X80 large OD 1422 mm line pipes
High-grade (API 5L X80) and large-diameter (OD 1422 mm) line pipes are used in the Sino–Russian eastern route gas pipeline project for high pressure (12 MPa) transmission, and this can significantly increase the transmission capacity and meet China's ...
Chunyong Huo +5 more
doaj +1 more source
Strain-Based Design Methodology of Large Diameter Grade X80 Linepipe [PDF]
Continuous growth in energy demand is driving oil and natural gas production to areas that are often located far from major markets where the terrain is prone to earthquakes, landslides, and other types of ground motion. Transmission pipelines that cross
Lower, Mark D.
core +2 more sources
Cet article présente une étude de la sensibilité à la fragilisation par l'hydrogène des joints soudés en acier API 5L X80 par les procédés SMAW et GTAW. En faisant varier les consommables utilisés et l'utilisation de la même température d'interpass, trois joints soudés différents ont été obtenus.
Bruno Allison Araújo +4 more
openaire +2 more sources
Abstract This study presents an experimental investigation conducted on a 40‐year‐old vintage X52 oil pipe segment to assess the growth behavior of near‐neutral pH stress corrosion cracking (SCC). Six cracks were introduced on the pipe specimen, each of which was associated with a unique combination of metallurgical and environmental condition.
Haotian Sun +5 more
wiley +1 more source
Natural tara and oak gall nut tannins, which lack corrosion inhibitive properties, were modified using gum arabic and tested against microbial corrosion induced by Acidithiobacillus thiooxidans under isothermal condition (28°C). Mild steel coated with the modified tannins was exposed to the causative under aerobic and anaerobic conditions. Based on the
Samuel Eshorame Sanni +4 more
wiley +1 more source
Strain based design considerations for spiral welded pipelines [PDF]
Pipelines are constructed in hostile environments where the occurrence of imposed plastic deformations can necessitate a strain based design approach. Under such conditions not only the strength and toughness properties have to be considered; also the ...
De Waele, Wim +3 more
core
Study of the thermomechanical behavior of API 5L X80 steel micro-alloyed with Nb-Ti through hot torsion tests [PDF]
The controlled rolling of high strength low alloy steel has been widely used in the production of large diameter pipes for the oil and gas industry. The thermo-mechanical control process (TMCP) is used to maximize grain refinement and achieve both higher strength and toughness in the steels.
Martins, Fernanda Huebra +1 more
openaire +3 more sources
The effect of the water-saturated supercritical carbon dioxide (scCO2) flow rate on the corrosion behavior of API 5L X80 steel at a temperature of 35°C and pressure of 80 bar was investigated. Tests were performed with the samples attached to a rotating shaft inside an autoclave.
da Silva de Sá, J. +6 more
openaire +2 more sources
Aqueous extract of Thevetia peruviana leaves were investigated as corrosion inhibitor for API 5L X80 pipeline steel in 1M H2SO4 solution using electrochemical and gravimetric techniques. The results reveal that T. peruviana inhibited the X80 pipeline steel corrosion in the acid medium in a concentration dependent manner.
Akens Hamilton-Amachree +1 more
openaire +1 more source

