Results 71 to 80 of about 1,400,800 (285)
Polymer Composites, EarlyView.Graphical abstract illustrating the fabrication of PLA and wood‐PLA composites via FDM and their subsequent mechanical testing, water absorption, and re‐drying evaluation. ABSTRACT Natural fiber‐reinforced thermoplastic composites have gained increasing attention due to their sustainability.
Weilong Xu +4 more
wiley +1 more source
Reinforcement of wood with natural fibers [PDF]
, 2013 This paper describes an experimental programme which examines the reinforcement in flexure of timber beams with composite materials based on natural fibers in the form of fabrics made from hemp, flax, basalt and bamboo fibers.
A. Borri +17 more
core +1 more source
Effect of Designed 3D Reinforcement in Mitigating Machining Damage on CFRP Plates
Polymer Composites, EarlyView.Effect of Edge Tufting on Surface Quality, Damage, and Mechanical Performance in CFRP Machining: A Comparative Topographical and Structural Analysis. ABSTRACT Composite materials made of carbon fiber‐reinforced epoxy (CFRP) are widely used in aerospace fields due to their high strength‐to‐weight ratio. However, due to low out‐of‐plane resistance, these
Thiago Luiz Lara Oliveira +2 more
wiley +1 more source
RGUHS Journal of Dental SciencesAim The aim of this study was to evaluate and compare the fracture resistance and patterns of fracture in unreinforced glass amp aramid fiber mesh reinforced maxillary complete dentures under dynamic fatigue loading.Methods Forty ...
Ancita Caroline Dsouza +2 more
doaj +1 more source
Polymer Composites, EarlyView.Electrospun nanofibre for load‐bearing composite materials. ABSTRACT Electrospun nanofibres are emerging nanomaterials prized for their scalability, high surface area to volume ratio and yield. Their effectiveness in improving the mechanical properties of fiber reinforced composites is widely reported. Nanofibres could activate multiscale toughness and
Usaid Ahmed Shakil, Petr Hájek
wiley +1 more source
Fatigue behaviour study on repaired aramid fiber/epoxy composites [PDF]
Journal of Aerospace Technology and Management, 2009 Aramid fiber reinforced polymer composites have been used in a wide variety of applications, such as aerospace, marine, sporting equipment and in the defense sector, due to their outstanding properties at low density. The most widely adopted procedure to
Edson Cocchieri Botelho +4 more
doaj
Polymer Composites, EarlyView.Experimental and numerical investigation on impact‐tolerance efficient evaluation of soft TPU composites. ABSTRACT This study combines experimental characterization and numerical modeling to investigate the impact behavior of aramid fiber–reinforced composites incorporating a thermoplastic polyurethane (TPU) matrix. Low‐velocity impact (LVI) tests were
Shunqi Zhang +6 more
wiley +1 more source
Concepts for the development of light-weight composite structures for rotor burst containment [PDF]
, 1977 Published results on rotor burst containment with single materials, and on body armor using composite materials were used to establish a set of hypotheses about what variables might control the design of a weight-efficient protective device.
Holms, A. G.
core +1 more source
Polymer Composites, EarlyView.Schematic illustration of a hierarchical recycling approach that preserves reinforcing fiber orientation. ABSTRACT Current recycling methods for polymer matrix composites produce short, unoriented carbon fibers, limiting their use to intermediate‐strength applications.
Carol Winnifred Rodricks +3 more
wiley +1 more source
Non-destructive testing on aramid fibres for the long-term assessment of interventions on heritage structures [PDF]
, 2015 High strength fibre reinforced polymers (FRPs) are composite materials made of fibres such as carbon, aramid and/or glass, and a resin matrix. FRPs are commonly used for structural repair and strengthening interventions and exhibit high potential for ...
Ceravolo, Rosario +4 more
core +2 more sources