Results 121 to 130 of about 90,830 (223)
Surface and Interface Analysis, Volume 58, Issue 3, Page 151-163, March 2026.ABSTRACT The present work focuses on investigating the effect of increasing Inconel 625 Fe content on the oxide film composition and corrosion behaviour through XPS and cyclic potentiodynamic polarisation (CPP) studies. Different proportions of ASTM A182 F22 steel and Inconel 625 were arc‐melted to achieve a range of Fe contents (2–15 wt.%) in the ...
J. C. Lourenço +5 more
wiley +1 more source
steel research international, Volume 97, Issue 3, Page 1201-1225, March 2026.This review investigates the processing‐microstructure‐property relationships in ferritic stainless steels (FSSs). It highlights advances in deformation behavior, heat treatments, surface modifications, and alloying effects. Theoretical models, including Johnson‐Mehl‐Avrami‐Kolmogorov, Arrhenius, nucleation theory, and diffusion theories, are discussed
Shahab Bazri +4 more
wiley +1 more source
Mechanical Properties and Corrosion Behavior of Low Carbon Steel Weldments [PDF]
, 2013 This research involves studying the mechanical properties and corrosion behavior of low carbon steel (0.077wt% C) before and after welding using Arc, MIG and TIG welding.
Majid H. Abdulmajeed +2 more
core
steel research international, Volume 97, Issue 3, Page 1369-1383, March 2026.The processability of the E11018‐G by laser powder directed energy deposition (LP‐DED) is investigated. The effects of powder moisture, ambient humidity, and laser remelting on LP‐DED parts’ porosity are shown. A strong influence of the atomizing gas is observed.
Josu López‐López +7 more
wiley +1 more source
Scientific ReportsTo address the challenge of porosity suppression in laser-arc hybrid welding of high-nitrogen steel, a weakly coupled laser-arc welding method suitable for high-nitrogen steel is proposed.
Fengde Liu, Kai Ning, Xiaojun Liu
doaj +1 more source
Establishment on the chloride resistant clad rebar weld process in simulated seawater
Case Studies in Construction MaterialsTo enhance the weld process of the new type of clad rebar construction in the marine environment, the weld process of the clad rebar was established. Four different weld processes were used to weld the clad rebars. The microscopy of the welded joints was
Zecheng Zhuang +9 more
doaj +1 more source
Simulation of a Gas Tungsten Arc Welding Process in COMSOL [PDF]
, 2012 The purpose of this project is to model the transport phenomena (heat transfer, fluid flow, and current flow) in a gas tungsten arc welding (GTAW) process using COMSOL Multiphysics.
Hu, Junling, Yang, Xiang
core
Small Structures, Volume 7, Issue 3, March 2026.Cross‐sectional Li–LLZO interfacial morphologies obtained by ultrasonic welding in seconds at room temperature. Solid‐state batteries (SSBs) are widely regarded as promising next‐generation energy storage technology due to their potential for enhanced safety and higher energy density compared to conventional Li‐ion batteries.
Mikihisa Fukuda +6 more
wiley +1 more source
Power arc welder touch-started with consumable electrode [PDF]
, 1966 Power arc welder formed as a hand-held welding gun touch-starts, retracts a consumable electrode to create the desired arc, and then commences feeding of the consumable electrode at the rate required to form the intended bead or spot.
Jeannette, J. C.
core +1 more source
Fatigue Lifetime Assessment of HFMI‐Treated Welded Joints According to the Peak Stress Method
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 3, Page 790-819, March 2026.ABSTRACT High‐frequency mechanical impact (HFMI) is an effective post‐weld treatment that enhances fatigue strength by inducing compressive residual stresses, localized strain hardening, and increasing weld toe radii. The peak stress method (PSM) was recently extended to evaluate the fatigue strength of HFMI‐treated steel joints under uniaxial loading ...
Alberto Campagnolo +2 more
wiley +1 more source