Results 191 to 200 of about 22,275 (307)

Anomaly prediction of CT equipment based on IoMT data. [PDF]

BMC Med Inform Decis Mak, 2023
Wang C, Liu Q, Zhou H, Wu T, Wu T, Liu H, Huang J, Zhuo Y, Li Z, Li K.   +9 more
europepmc   +1 more source

Influence of Carbon Nanoparticles on Electrically Induced Wear of Grease‐Lubricated Steels

Advanced Materials Interfaces, EarlyView.
When an electric current enters a pair of rubbing surfaces, enormous damage takes place. In this research, how such damage occurs in the presence of protective grease and the mitigation with added carbon nanoparticles, were investigated. It was discovered that those particles regulate transport and interfacial electrical stability of the grease ...
Mohammad Humaun Kabir, Darrius Dias, Jacob Bons, MD Wasek Foysal, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Ultrahigh Temperature Purification of Graphite for the Development of a Continuous Process. [PDF]

ACS Omega
Tan Y, Duchesne M, Doninger A, Meyers M, Barsukov IV.   +4 more
europepmc   +1 more source

Assessing TiO2/Chitosan‐Based Hydrogels for Water Remediation: Sunlight‐Driven Degradation of Antibiotics in Water

Advanced Materials Interfaces, EarlyView.
Chitosan–TiO2 composite hydrogels combine adsorption of organic pollutants with photocatalysis, allowing to remove 85% of a broadly diffused antibiotic (sulfamethoxazole) under direct sunlight irradiation, opening great promises for point‐of‐use, outdoor applications.
Beatrice Cerea, Giovanni Ribaudo, Alessandra Gianoncelli, Matteo Ferroni, Irene Vassalini, Ivano Alessandri   +5 more
wiley   +1 more source

A Data-Driven Loose Contact Diagnosis Method for Smart Meters. [PDF]

Sensors (Basel)
Luan W, Huang Y, Zhao B, Cai H, Han Y, Liu B.   +5 more
europepmc   +1 more source

Vat Polymerization 3D Printing for Controlled Drug Release Applications

Advanced Materials Technologies, EarlyView.
ABSTRACT Vat polymerization (VP) 3D printing, a light‐based additive manufacturing technique, has emerged as a promising technique for fabricating complex drug delivery systems with high precision and spatial resolution. This layer‐by‐layer manufacturing process enables the creation of intricate geometries and customizable architectures, which are ...
Hafiz Busari, O. Thompson Mefford, M. Aaron Vaughn   +2 more
wiley   +1 more source

Toward Large Ablations With Single-Needle High-Frequency Irreversible Electroporation In Vivo. [PDF]

IEEE Trans Biomed Eng
Aycock KN, Campelo SN, Salameh ZS, Davis JMK, Iannitti DA, McKillop IH, Davalos RV.   +6 more
europepmc   +1 more source

ARC Stent Thrombosis Timing Subacute [PDF]

, 2020
openaire   +1 more source

Smart and Sustainable Sizing: Investigating the Sensing Behavior of Glass Fabrics Coated With Waterborne Polyurethane/Graphene Dispersions

Advanced Materials Technologies, EarlyView.
Waterborne polyurethane/graphene formulations are developed as piezoresistive coatings on glass fabric to enable flexible strain sensing. The graphene‐enabled conductive network provides a stable electromechanical response under cyclic compression. The coating demonstrates reliable pressure‐dependent resistance changes, highlighting its potential for ...
Vishnu Vijayan Pillai, Premika Govindaraj, Sai Aditya Pradeep, Olivia Sequerth, Srikanth Pilla, Franz Konstantin Fuss, Peter Kingshott, Nishar Hameed, Nisa V Salim   +8 more
wiley   +1 more source

Wavelet-based arcing signal source localization algorithm using a compact multi-square microstrip antenna. [PDF]

Sci Rep
Amirruddin M, Adzman MR, Mohd Affendi NA, Isa M, Idris MH, Abd Halim S, Lehtonen M.   +6 more
europepmc   +1 more source