Results 141 to 150 of about 678,286 (388)

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Das magnetische Verhalten von Luft, Argon und Helium in Beziehung zu Sauerstoff [PDF]

, 1907
Paul Tänzler
openalex   +1 more source

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

On the Deformation Behavior of Metastable CrMnNi Steels Processed by Directed Energy Deposition in Different Temperature Regimes

Advanced Engineering Materials, EarlyView.
In the present study, metastable CrMnNi steels with varying chemical compositions and a concomitantly altered stacking fault energy are processed via directed energy deposition and afterwards tested via tensile tests at different temperatures. The present study shows the influence of the manufacturing process on the elemental deformation mechanisms for
Julia Richter, Thomas Wegener, Florian Stredak, Gert Bartzsch, Steffen Scherbring, Javad Mola, Olena Volkova, Stefan Böhm, Thomas Niendorf   +8 more
wiley   +1 more source

Direct Electron Detection Electron Energy‐Loss Spectroscopy: Speeding Up 2D Analytical In Situ Transmission Electron Microscopy for Aluminum Alloys

Advanced Engineering Materials, EarlyView.
Scanning transmission electron microscopy imaging techniques are an essential tool to document dynamic developments, such as precipitation in aluminum alloys, during in situ heating experiments using transmission electron microscopy. However, in many cases, chemical information is required to interpret complex nanoscale processes.
Evelin Fisslthaler, Martina Dienstleder, Judith Lammer, Moritz Theissing, Daniel Knez   +4 more
wiley   +1 more source

The Triple Point of Argon as a Thermometric Fixed Point [PDF]

, 1958
R. A. H. Pool, B. D. C. Shields, L. A. K. Staveley   +2 more
openalex   +1 more source

Laboratory‐Scale Procedure for Evaluating the Flux Efficiency on Melt Cleanliness and Tensile Properties of Recycled Aluminum Alloys

Advanced Engineering Materials, EarlyView.
A laboratory‐scale procedure is developed to evaluate the efficiency of melt‐cleaning and drossing fluxes during aluminium alloy recycling, studying their effects on melt cleanliness and tensile properties of secondary foundry alloys. This work provides a practical tool for foundries and aluminium refiners to assess the efficiency of salt fluxes in ...
Veronica Milani, Giulio Timelli
wiley   +1 more source

The Influence of Nitrogen in Ar+N2 Mixture on Parameters of High-Temperature Device with Electric Arc

Acta Polytechnica, 2013
The paper presents the results of numerous experiments carried out on a high temperature device consisting of an arc heater with intensively blasted electric arc and reaction chambers connected to its output. The influence of nitrogen mass concentration (
Ivana Jakubova, Josef Senk, Ilona Laznickova   +2 more
doaj  

Der Effekt des elektrischen Feldes auf Linien des Argons und des Sauerstoffs [PDF]

, 1920
E. Böttcher, F. Tuczek
openalex   +1 more source

Microstructural Evolution and Mechanical Property Degradation of Sn0.5Ag0.7Cu5Bi Solder Joints with High Indium Alloying

Advanced Engineering Materials, EarlyView.
This study identifies 12 wt% indium (In) as the optimal composition for Sn0.5Ag0.7Cu5Bi solder joints, achieving 87% ductile fracture and 81% suppression of intermetallic compound (IMC) growth versus 4 wt% In. High‐In alloys (15–17 wt%) show abnormal IMC thickening due to thermal activation.
Liuwei Wang, Huidong Gu, Xiaojing Wang, Shanshan Cai, Saad Alshammari, Gaber A. M. Mersal, Yanlai Wang, Xulei Wu, Hanhui Lei, Juanna Ren, Mohamed M. Ibrahim, Terence X. Liu   +11 more
wiley   +1 more source