Results 131 to 140 of about 208,305 (321)
ENERGY &ENVIRONMENTAL MATERIALS, Volume 9, Issue 6, November 2026.The Zr‐doped coralloid μSi encapsulated within an N‐coordinated dual‐carbon network is fabricated by an Al‐Si melt modification integrated with in‐situ interfacial strategy, consequently improving the ionic diffusion behaviors. Micro‐scale silicon (μSi) anodes are promising candidates for enhancing energy density of lithium‐ion batteries, yet their ...
Juxuan Ding +5 more
wiley +1 more source
Alabama warm mix asphalt field study : final report. [PDF]
The Alabama Department of Transportation hosted a warm mix asphalt field demonstration in August 2007. The warm mix asphalt technology demonstrated was Evotherm Dispersed Asphalt Technology. The WMA and hot mix asphalt produced for the demonstration were
de Fortier Smit, Andre +5 more
core
Laboratory performance of asphalt rubber mixtures [PDF]
, 2009 Asphalt rubber mixtures are one of the most promising techniques to extend the service life of asphalt pavement overlays. Asphalt rubber binder is composed of crumb rubber from reclaimed tires and conventional asphalt.
Trichês, Glicério +4 more
core
Material Characterization of Lignin‐Filled Polypropylene Composites
Journal of Applied Polymer Science, Volume 143, Issue 40, October 20, 2026.Ground and spray‐dried lignin powders are compared as fillers for polypropylene composites. Differences in powder preparation methods are associated with differences in powder characteristics and composite behavior after melt compounding. Spray‐dried lignin produces smaller particles and fewer large agglomerates, while a 5 wt% lignin loading provides a
Sungjun Hwang +3 more
wiley +1 more source
Hot mix asphalt tender zone [PDF]
Approximately 500 million tons of hot mix asphalt (HMA) are placed in the United States each year. With this large quantity of HMA, it is expected that some construction problems will occur from time to time. One problem that has been observed for years,
Decker, Dale +3 more
core
Journal of Applied Polymer Science, Volume 143, Issue 39, October 15, 2026.This work explores the use of various fillers, including eggshell powder, feather meal, peanut hulls, and sawdust to reinforce a base binder GFS90 (comprised of 90 wt.% sulfur, 5 wt.% chicken fat, and 5 wt.% sunflower oil). The resulting composites showed impressive compressive strengths ranging from 15.3 to 36.2 MPa, making them a potential ...
Bárbara G. S. Guinati +5 more
wiley +1 more source
Asphalt fume exposures during the manufacture of asphalt roofing products: current practices for reducing exposures [PDF]
"This document represents a collaborative effort of the National Institute for Occupational Safety and Health (NIOSH), the National Roofing Contractors Association (NRCA), the Asphalt Roofing Manufacturers' Association (ARMA), the Asphalt Institute (AI),
core
Laboratory Performance Evaluation of CIR-Emulsion and it Comparison Against CIR-Form Test Result from Phase II, Final Report TR-578 Phase III, December 2009 [PDF]
, 2009 Currently, no standard mix design procedure is available for CIR-emulsion in Iowa. The CIR-foam mix design process developed during the previous phase is applied for CIR-emulsion mixtures with varying emulsified asphalt contents.
core
Journal of the Fuel Society of Japan, 1963 Systematically blown asphalts were prepared, and their dielectric properties were measured at the frequency of 30c/sec-1Mc/sec.Difference of the properties due to the raw stock and degree of blowing, and relationship between the properties and other ones were studied.Moreover, a few informations were obtained from the measurement of the properties by ...
openaire +4 more sources