Results 31 to 40 of about 356,373 (287)
Compressive Strength of Concrete Cylinders by Different Preparation Methods: Sulphur, Neoprene Pads and Grinding [PDF]
, 2018 The purpose of this evaluation is to compare the effects of four types of cylinder preparation methods prior to compressive strength testing in accordance to ASTM C ...
Halsey, Lieska, Heyen, Wally
core +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, EarlyView.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Flame retardancy and mechanical properties of poegmah compatibilized rice husk filled polypropylene composites [PDF]
, 2009 Flammability of Polypropylene, PP has restricted its usage as a versatile synthetic polymer. The addition of flame retardants will lower the flammability of PP. However, it will lower the mechanical properties.
Adnan, Noorazlina
core
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser shock peening for enhancing fatigue performance of riveted aerospace aluminum joints. A comparative approach with cold expansion combines fatigue testing and synchrotron X‐ray methods. Integrating mechanical testing with residual stress and strain characterization provides insights into how different treatments affect the ...
Ogün Baris Tapar +6 more
wiley +1 more source
Current status of the small punch test standardization within the ASTM
Ubiquity Proceedings, 2018 Since 2014, considerable attention has been paid to the standardization of small punch test technique within the American Society of Testing and Materials (ASTM). In 2016 large inter-laboratory study has been launched within the ASTM subcommittee E10.2 -
R. Kopriva, M. Brumovsky, P. Petelova
doaj +1 more source
Advanced Engineering Materials, EarlyView.Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes +4 more
wiley +1 more source
Corrosion and Materials Degradation, 2022 Carbon steel rebar (ASTM A615) has been widely used in reinforced concrete (RC), but its susceptibility to chloride ions remains a critical issue. Low alloy chromium steel has been used to increase corrosion resistance and extend service life, such as in
Yi Lu +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Excellent combinations of strength and impact toughness are obtained in a bilayer composite of high‐strength carbide‐free bainitic (CFB) steel and high‐ductility twinning‐induced plasticity (TWIP) steel. The composite absorbs energy at small strains when the notch is placed on the TWIP side and at high strains when the notch is placed on the CFB side ...
Kendra Hawke +5 more
wiley +1 more source