Results 141 to 150 of about 175,846 (341)

Influence of an Al‐Doped ZnO Interface Layer on the Thermochromic Properties of VO2 Thin Films Deposited by RF Magnetron Sputtering

open access: yesAdvanced Engineering Materials, EarlyView.
Herein the metal‐to‐insulator transition is investigated when depositing vanadium dioxide (VO2) on glass or aluminum‐doped zinc oxide (AZO). O2 flow tuning during the deposition and additional post annealing are effective to control the metal‐to‐insulator transition. However, the VO2/AZO/glass stack reveals an increase in the transition temperature and
Eduard Llorens Balada   +3 more
wiley   +1 more source

The origin and composition of the atmosphere

open access: yesEos, Transactions American Geophysical Union, 1929
See report in this Volume presented at eleventh annual meeting of the Section, May 1, 1930.
openaire   +2 more sources

Mantle redox state drives outgassing chemistry and atmospheric composition of rocky planets. [PDF]

open access: yesSci Rep, 2020
Ortenzi G   +10 more
europepmc   +1 more source

Concentration and Composition of Atmospheric Aerosols from the 1995 SEAVS Experiment and a Review of the Closure between Chemical and Gravimetric Measurements [PDF]

open access: bronze, 2000
Elisabeth Andrews   +7 more
openalex   +1 more source

Design and Evaluation of 3D‐Printed Polylactic Acid Composites Reinforced with Biodegradable Bamboo Powder and Jute Powder

open access: yesAdvanced Engineering Materials, EarlyView.
The study investigates 3D‐printed polylactic acid (PLA) composites with biodegradable bamboo and jute powder fillers. Mechanical, thermal, structural properties, and rheological behavior are discussed to evaluate composite performance. Morphological characterization indicates uniform dispersion and adhesion of the fillers in the PLA matrix with the ...
Vimukthi Dananjaya   +4 more
wiley   +1 more source

A Study on Thermal Expansion and Thermomechanical Behavior of Composite Metal Foams

open access: yesAdvanced Engineering Materials, EarlyView.
The coefficient of thermal expansion of steel–steel composite metal foam (S‐S CMF) is shown to be lower than that of bulk stainless steel while its performance under compression demonstrate excellent mechanical stability and strength at all temperatures with gradualsoftening from 400 to 600 °C.
Zubin Chacko   +2 more
wiley   +1 more source

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag   +3 more
wiley   +1 more source

Enhanced Mechanical Properties of Injectable Chitosan–Guar Gum Hydrogel Reinforced with Bacterial Cellulose Nanofibers for Tissue Engineering Applications

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents the development and characterization of injectable nanocomposite hydrogels based on N‐succinyl chitosan, oxidized guar gum, and bacterial cellulose nanofibers. Emphasizing enhanced mechanical properties and biocompatibility, the hydrogels exhibit fast gelation, improved structural integrity, and reduced swelling. Their potential for
Raimundo Nonato Fernandes Moreira Filho   +8 more
wiley   +1 more source

Home - About - Disclaimer - Privacy