Results 41 to 50 of about 9,888 (260)
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
New Technique for Aerosol Detection in Haze Day Using Side‐Scattering Lidar and Its Inversion Method
Earth and Space Science, 2020 The new side‐scattering lidar using two charge‐coupled device cameras and one CW laser is developed to measure the near‐ground aerosol profiles in haze day, which is a powerful tool and is most interested for the environmental and meteorological agencies.
Zhenzhu Wang +4 more
doaj +1 more source
Evaluation of High Cloud Product of ECMWF Over South China Sea Using CALIOP
Earth and Space Science, 2022 High clouds are globally widespread and are crucially important to global radiative processes and to the thermal balance of the Earth. Active remote sensing measurements can provide more reliable detection of optically thin cirrus clouds than passive ...
Wenqiang Lu +7 more
doaj +1 more source
Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects
Advanced Engineering Materials, EarlyView.This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Atmosphere, 2019 Through the observation of ground-based LIDAR and satellite sensors, the weather conditions of continuous foggy-hazy alternations in the Huainan region from 26 December 2016 to 5 January 2017 were analyzed and observed.
Songlin Fu +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Retrieval of Solar Shortwave Irradiance from All-Sky Camera Images
Remote SensingThe present work proposes a new model based on a convolutional neural network (CNN) to retrieve solar shortwave (SW) irradiance via the estimation of the cloud modification factor (CMF) from daytime sky images captured by all-sky cameras; this model is ...
Daniel González-Fernández +16 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source