Results 141 to 150 of about 208,968 (293)
steel research international, EarlyView.Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan +8 more
wiley +1 more source
steel research international, EarlyView.An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén +3 more
wiley +1 more source
Austenite Grain Growth Behavior of 40CrNiMoA Alloy Structural Steel
TeshugangThe austenite grain size is an important factor affecting the strength and toughness of 40CrNiMoA alloy structural steel. To fully explore the performance potential of 40CrNiMoA steel， it is necessary to investigate its grain evolution behavior during ...
Zhou Min +4 more
doaj
Teshugang, 2005 According to the solubility product theory of second phase in austenite, Ostward ripening theory, grain size control theory and precipitation strengthening theory, the probability for formation of inclusions in austenite and the inclusion size control ...
雍岐龙 +4 more
doaj
steel research international, EarlyView.This review explains how impurities from recycled scrap affect steel production and performance. Even small amounts (far below 1%) of these impurities can change how steel behaves during fabrication but also affect the properties of the end product. With better understanding and targeted countermeasures, these challenges can be managed, enabling wider ...
Oleksandr Glushko, Ronald Schnitzer
wiley +1 more source
steel research international, EarlyView.High Nb (2.4 wt.%) addition to Maraging 300 steel drives lattice distortion and nanoscale Nb–Mo‐rich precipitation, confirmed by energy‐dispersive X‐ray spectroscopy mapping (Mo ~5.4 wt.%, Nb ~2.5 wt.%). Nanoindentation reveals strong matrix hardening (H >4.8 GPa) at 480°C aging, while 560°C induces ~1.92 vol.% reverted austenite, enabling tunable ...
Laylla Sharon B. Peixoto +9 more
wiley +1 more source
steel research international, EarlyView.Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König +2 more
wiley +1 more source
Teshugang, 2016 The effect of process of warm-forging at 880 ~ 930 °C on growth of austenite grain of gear steel 20CrMnTiH3 is analyzed by examination of physicochemistry and original material austenite grain size to get that the austenite of steel is easy abnormally ...
白瑞娟 +5 more
doaj
Micro‐Mechanism Informed Neural Networks for Process‐Property Prediction in Laser Powder Bed Fusion
Artificial Intelligence for Engineering, EarlyView.Hard physics embedding, where neural networks learn residuals relative to analytical baselines, substantially outperforms soft loss‐function constraints for extrapolation in LPBF process–property prediction. Physics integration architecture determines generalization capability more than constraint quantity.
Yo‐Lun Yang
wiley +1 more source
CrystalsCrystal grain size control in steel is critical for achieving mechanical properties. This study investigates the effectiveness of microalloying with titanium, niobium, zirconium, and yttrium to inhibit grain growth with the pinning effect. The comparison
Jaka Burja, Samo Tome, Aleš Nagode
doaj +1 more source