Results 101 to 110 of about 822,289 (227)

Effect of Oxygen and Nitrogen Oxide Gas Concentration on Corrosion of 310N Stainless Steel in Solar Salt at 600°C

Materials and Corrosion, Volume 77, Issue 9, Page 1579-1594, September 2026.
Schematic depicting corrosion layer formation and changes in stainless steel exposed to Solar Salt at 600°C for 1000 h under different atmospheres: (a) N2 accelerates salt decomposition, producing nitrite and oxide ions, causing severe corrosion. (b) Adding O2 reduces nitrite ions formation, resulting in less corrosion than N2 alone.
Sumit Kumar, Srinivasan Swaminathan, Rene Hesse, Wenjin Ding, Thomas Bauer   +4 more
wiley   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, Volume 77, Issue 9, Page 1399-1423, September 2026.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

Chromium Salt: A Review of Salt Formation, Hygroscopic Properties, and Impact on 316 L Corrosion in Hydrochloric Acid

Materials and Corrosion, Volume 77, Issue 9, Page 1424-1437, September 2026.
This article examines the impact of externally introduced chromium compounds on the localized corrosion of 316 L stainless steel in acidic chloride environments such as hydrochloric acid. While the corrosion resistance of 316 L relies on the formation of a chromium‐rich passive oxide layer, industrial conditions may expose the steel to various chromium
Florence Lequien
wiley   +1 more source

Creep characteristics of austenitic stainless steel foil at elevated temperature [PDF]

, 2013
High efficiency and compact recuperator with thin foil corrugated air cell as the primary surface is employed in clean and efficient microturbine system (100 kW).
Shahrul Azhar, Ilya Izyan
core  

Influence of Strain Rate on the Strain Hardening Behavior of a Lean Duplex Stainless Steel

MetalMat, Volume 3, Issue 3, September 2026.
The aim of this study was to examine how strain rate influences the compressive strain‐hardening behavior of a lean duplex stainless steel LDX 2101. Microstructural analysis using electron backscatter diffraction (EBSD) revealed a strain‐induced austenite‐to‐martensite transformation.
Akilakpa Sawyerr, Eric Kotei T. Addison, Martin Owusu‐Mensah, Abdul Jaleel Mohammed, Daolun Chen   +4 more
wiley   +1 more source

Actuation Strategies for Underwater Jet‐Propelled Soft Robots

Journal of Field Robotics, Volume 43, Issue 6, Page 3868-3892, September 2026.
ABSTRACT This review article examines jet‐propulsion mechanisms in underwater soft robotic systems, focusing exclusively on physically fabricated and experimentally validated robots. Covering research published from 2013 to 2025, this study classifies and evaluates jet‐propulsion robots based on their actuation mechanisms.
Angel Kitone, Mohammed Anteet, Pawandeep S. Matharu, Yara Almubarak   +3 more
wiley   +1 more source

Creep Performance of Stainless Steel 316 Brackets: Insights From Conventional and Advanced Modeling Approaches

steel research international, Volume 97, Issue 9, Page 4889-4904, September 2026.
Creep behavior of SS 316 brackets is examined through experiments, conventional creep laws, and advanced constitutive modeling. Long‐term deformation, stress redistribution, and life prediction are compared under service‐relevant loads. The study highlights the limits of classical models and demonstrates improved accuracy using advanced approaches for ...
Mohsin Sattar, Jan Hosek, Maaz Akhtar, Uliana Finaeva, Muhammad Muzamil, Naser A. Alsaleh, Asad A. Zaidi, Barun Haldar   +7 more
wiley   +1 more source

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, Volume 97, Issue 9, Page 4483-4493, September 2026.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Influência das condições de processo sobre as descontinuidades e resistência à cavitação de revestimentos soldados sobre aço CA-6NM [PDF]

, 2012
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia MecânicaA erosão por cavitação causa enormes prejuízos para as empresas geradoras de energia elétrica, pois compromete o ...
Beiler, Denilson Rogério
core  

Green and sustainable anticorrosive action of Punica granatum peel extract on austenitic stainless steels in 1M HCl through electrochemical investigations

Frontiers in Built Environment
The corrosion resistant nature and long-lasting properties made stainless steel very popular in many sectors. There are different grades of stainless steel (SS), in which the category of austenitic steels like SS 304 and SS 202 are the most common and ...
K. Krishnanjana, G. Mohan Ganesh
doaj   +1 more source