Results 71 to 80 of about 4,855 (199)
Effect of Adding Copper Foils on Seam Welding Joints of 304 Austenitic Stainless Steel
Diyala Journal of Engineering Sciences, 2014 The aim of this work is to study the effect of adding copper (C10200 AISI) foils on the welding joint of the austenitic stainless steel type (AISI 304).The austenitic stainless steel has low weldability by resistance welding where the concentrated ...
Ammar Azeez Mahdi +2 more
doaj +1 more source
steel research international, EarlyView.Creep behavior of SS 316 brackets is examined through experiments, conventional creep laws, and advanced constitutive modeling. Long‐term deformation, stress redistribution, and life prediction are compared under service‐relevant loads. The study highlights the limits of classical models and demonstrates improved accuracy using advanced approaches for ...
Mohsin Sattar +7 more
wiley +1 more source
steel research international, EarlyView.Prebending of 304L/Q345R cladded plates significantly alters the subsequent weld thermal cycle and modifies the local interfacial microstructure. Combined electron backscatter diffraction (EBSD) and microscopy analysis demonstrates that deformation twinning, martensitic transformation, and defect initiation are concentrated at the trimaterial junction,
Ali Fahem +2 more
wiley +1 more source
工程科学与技术, 2023 To explore both static and seismic performances of stainless steel beam-to-column minor-axis joints, a total of four minor-axis joints with end-plate connections were designed and fabricated, involving two austenitic stainless steel joint specimens and ...
Jundong GAO +5 more
doaj
steel research international, EarlyView.An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén +3 more
wiley +1 more source
MATEC Web of Conferences, 2018 Nowadays engine capacities of vehicles spread in a wide range due to different vehicle power demands. Power density of engines affects exhaust gas and therefore exhaust gas temperature varies from 650 °C to 1000 °C in exhaust manifolds.
Çelik G. Aktaş +3 more
doaj +1 more source
Acta Metallurgica Slovaca, 2017 This paper investigates the changed in the microstructure in HAZ of the dissimilar weld between carbon steel and 304 austenitic stainless steel. Continuous cooling transformation diagrams (CCT), peak temperature profiles and cooling rates can be used to ...
Le Thi Nhung +3 more
doaj +1 more source
steel research international, EarlyView.This review explains how impurities from recycled scrap affect steel production and performance. Even small amounts (far below 1%) of these impurities can change how steel behaves during fabrication but also affect the properties of the end product. With better understanding and targeted countermeasures, these challenges can be managed, enabling wider ...
Oleksandr Glushko, Ronald Schnitzer
wiley +1 more source
steel research international, EarlyView.Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König +2 more
wiley +1 more source
steel research international, EarlyView.Serrations and stepwise austenite phase transformation were observed in cold‐rolled and annealed medium manganese steels. By in situ XRD experiments, these two phenomena were studied simultaneously. The results show that DSA leads to the creation of PLC bands and load drops in the specimen.
Shahroz Ahmed +6 more
wiley +1 more source