Results 111 to 120 of about 18,384 (203)
Fatigue behavior of welded austenitic stainless steel in different environments
Results in Physics, 2014 The fatigue behavior of welded austenitic stainless steel in 0.5 M hydrochloric acid and wet steam corrosive media has been investigated. The immersion time in the corrosive media was 30 days to simulate the effect on stainless steel structures/equipment
D.S. Yawas, S.Y. Aku, S.O. Aluko
doaj +1 more source
ChemSusChem, Volume 19, Issue 14, 29 July 2026.Steel‐supported, PGM‐free NiMo cathodes and anodized Ni‐coated steel anodes enable an ionomer‐free anion exchange membrane water electrolyzer. The fully noble‐metal‐free single cell delivers 1 A cm−2 at 1.92 V in 1 M KOH (60 °C) with stable operation over 60 h under dynamic conditions, demonstrating a scalable approach to cost‐effective green hydrogen ...
Lukas Heinius +14 more
wiley +1 more source
Creep characteristics of austenitic stainless steel foils under oxidative and non-oxidative environment [PDF]
, 2015 Compact and high efficiency recuperator with thin foil corrugated air cell as the primary surface is employed in clean and efficient microturbine system (100 kW).
Mohammed Kadhim, Fatimah
core
International Journal of Electrochemical Science, 2017 Austenitic stainless steel alloys are used in different food industry applications, including the preparation and storage of acidified carbonated soft drinks.
D. Mareci +3 more
doaj +1 more source
Advanced Engineering Materials, Volume 28, Issue 13, 8 July 2026.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
The influence of welding parameters and parent plate metallurgical characteristics on solidification of austenitic stainless steel weld metals [PDF]
, 1988 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The present work reports the effect of heat input, cooling rate, parent plate deformation and restraining conditions on the formation and morphology of ...
Hosseinioun, MM
core
Effect of Corrosive Factors on Progression of Pitting Corrosion of Welded SUS304 Steel under Freezing and Thawing Corrosive Environment [PDF]
, 2012 It has been reported that pitting corrosion occurs in stainless steel under the specific conditions which a corrosion factor superimposes. In cold and snowy area, welded structures on the outdoors are exposed to combinational environment of the salt ...
石塚, 和則 +5 more
core +1 more source
Chinese Journal of Mechanical EngineeringNon-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.
Chengwu Yao +3 more
doaj +1 more source
Advanced Science, Volume 13, Issue 39, 13 July 2026.Precipitation‐modulated recrystallization enables a programmable bimodal harmonic architecture in a high‐entropy alloy, delivering 1–2 GPa yield strength with >10% ductility from −196 °C to 700 °C. The resulting broad‐temperature robustness arises from the synergy of dual‐mode nanoprecipitation, harmonic core–shell topology, and temperature‐adaptive ...
Wei Li +5 more
wiley +1 more source
Mixing Behavior of Natural Gas and Hydrogen in a High‐Efficiency Vane (HEV) Static Mixer
Energy Science &Engineering, Volume 14, Issue 7, Page 3211-3225, July 2026.Static mixers play a crucial role in the safe transport of hydrogen‐blended natural gas. Computational fluid dynamics (CFD) was employed to investigate the effects of structural parameters of the HEV static mixer on the mixing behavior and homogeneity of natural gas and hydrogen. The modeling approach was well validated against experimental data.
Xiang Zhou +5 more
wiley +1 more source