Results 81 to 90 of about 18,384 (203)
Estudo de soldagem do aço inoxidável austenítico TP 347H para prevenir a corrosão localizada "gume de faca" [PDF]
, 2006 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia Mecânica.Durante uma parada geral para manutenção de uma planta industrial de MVC (mono-cloreto de vinila) foi constatada falha ...
Sales, Amilcar Andrade
core
Wear maps for TiC composite based coatings deposited on 303 stainless steel [PDF]
, 2014 Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, Ghulam +3 more
core +1 more source
Microstructure and Properties of Low-nickel Austenitic Stainless Steel14.0Cr-1.1Ni-9.2Mn-0.30Cu
Teshugang, 2023 14.0Cr- 1. 1Ni-9.2Mn-0.30Cu stainless steel was developed on the basis of13.36Cr- 1. 12Ni- 11.2Mn low-nickel austenitic stainless steel, and the metallographic structure, microstructure, mechanical properties and forming properties of austenitic ...
吴海林 +4 more
doaj
steel research international, EarlyView.This study validates a recycling pathway for converting interconnect assemblies from end‐of‐life SOC stacks into commercial‐grade AISI 304 steels. Using scrap‐based steelmaking operations, austenitic cast steels with <4.0% δ‐ferrite are successfully produced.
Jeraldine Lastam +7 more
wiley +1 more source
Hydrogen Embrittlement Susceptibility of Super Duplex Stainless Steels [PDF]
, 2010 This thesis describes the metallurgical and environmental factors that influence hydrogen embrittlement of super duplex stainless steels and presents a model to predict the rate at which embrittlement occurs.
Alsarraf, Jalal
core
Numerical Simulation of the Strength and Plasticity Performance in Austenitic Stainless Steel
High Temperature Materials and Processes, 2013 The effect of temperature and alloy content on the strength and plasticity of austenitic stainless steel was investigated in this paper. A series of expressions for quantitative calculation via computer were obtained according to the experimental data ...
Li Dongsheng, Dai Qixun, Cheng Xiaonong
doaj +1 more source
Exploiting Residual Elements Arising from Scrap Steel in Future Sustainable Steel Alloy Design
steel research international, EarlyView.Herein, the effects of residual elements Cu and Sn on grain growth, recrystallization, and phase transformation in C–Mn steel are summarized, and a case study is presented on how the presence of residual elements can be exploited to reduce deliberate Nb microalloying while achieving the same grain size control and strength during thermomechanical ...
Claire Davis +5 more
wiley +1 more source
Influência das condições de processo sobre as descontinuidades e resistência à cavitação de revestimentos soldados sobre aço CA-6NM [PDF]
, 2012 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia MecânicaA erosão por cavitação causa enormes prejuízos para as empresas geradoras de energia elétrica, pois compromete o ...
Beiler, Denilson Rogério
core
steel research international, EarlyView.Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin +4 more
wiley +1 more source
Effect of Adding Copper Foils on Seam Welding Joints of 304 Austenitic Stainless Steel
Diyala Journal of Engineering Sciences, 2014 The aim of this work is to study the effect of adding copper (C10200 AISI) foils on the welding joint of the austenitic stainless steel type (AISI 304).The austenitic stainless steel has low weldability by resistance welding where the concentrated ...
Ammar Azeez Mahdi +2 more
doaj +1 more source