Results 161 to 170 of about 822,229 (216)

A Study on the Liquid Helium Temperature Tensile Property of Fe-21Cr-15Ni-5Mn-2Mo Austenitic Stainless Steel after Solution Treatment. [PDF]

Materials (Basel)
Zhang M, Wang C, Ma D, Liu Y, Wang W, Liang J, Fang C, Chu W, Huang C.   +8 more
europepmc   +1 more source

Combined role of molybdenum and nitrogen in Limiting corrosion and pitting of super austenitic stainless steel. [PDF]

Heliyon
Li B, Lang Y, Chen H, Feng H, Qu H, Sun X, Tian Z.   +6 more
europepmc   +1 more source

Comparison of conventional and severe shot peening effects on the microstructure, texture, roughness, hardness, and electrochemical behavior of austenitic stainless steel. [PDF]

Heliyon
Yazdani F, Rabiee SM, Jamaati R.
europepmc   +1 more source

Residual Stress Engineering for Wire Drawing of Austenitic Stainless Steel X5CrNi18-10 by Variation in Die Geometries-Effect of Drawing Speed and Process Temperature. [PDF]

Materials (Basel)
Selbmann R, Gibmeier J, Simon N, Kräusel V, Bergmann M.   +4 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Recrystallization in 304 Austenitic Stainless Steel

Materials Science Forum, 2004
A 304 austenitic stainless steel was deformed using hot torsion to study the evolution of dynamic recrystallization (DRX). The initial nucleation of dynamically recrystallization occurred by the bulging of pre-existing high angle grain boundaries at a strain much lower than the peak strain.
Dehghan-Manshadi, A, Beladi, H, Barnett, M R, Hodgson, P D   +3 more
openaire   +3 more sources

Austenitic Stainless Steels

2008
Abstract This chapter discusses the compositions, mechanical properties, phase structure, stabilization, corrosion resistance, and advantages of austenitic stainless steels. Austenitic alloys are classified and reviewed in three groups: (1) lean alloys, such as 201 and 301, which are generally used when high strength or high formability ...
openaire   +1 more source

Sliding wear of austenitic and austenitic-ferritic stainless steels

Metallurgical and Materials Transactions A, 2002
The dry sliding behavior of a 304L austenitic stainless steel and a duplex 2205 austenitic-ferritic stainless was investigated. The evolution of wear was characterized by the existence of a sliding-distance transition. In particular, wear passed from delamination to tribo-oxidation, with a reduction in wear rate. The occurrence of such a transition was
Straffelini, Giovanni, D. Trabucco, Molinari, Alberto   +2 more
openaire   +2 more sources

Plasma immersion ion implantation of stainless steel: austenitic stainless steel in comparison to austenitic-ferritic stainless steel

Surface and Coatings Technology, 1996
Abstract It has been shown previously in the literature that plasma immersion ion implantation (PHI) can increase the wear resistance of austenitic stainless steel without losing its corrosion resistance. In this work, the effect of PHI treatment on the microstructure and the properties of an austenitic (X6CrNiTi1810, AISI 321) and a duplex ...
C. Blawert, A. Weisheit, B.L. Mordike, R.M. Knoop   +3 more
openaire   +1 more source

Austenitic Stainless Steels

Abstract This article presents fractographs of austenitic stainless steels that failed by overload, fatigue, stress-corrosion cracking, and embrittlement. A small sampling of fractographs in the article illustrate a 316L test bar showing ductile microvoid dimples with variable sizing.
openaire   +2 more sources

The formability of austenitic stainless steels

JOM, 1997
This article reports the results of a study to determine the effects of austenite stability, with respect to the strain-induced transformation to martensite, on the formability of 300 series stainless steels. The effects were evaluated as a function of alloy content, deformation temperature, and deformation rate.
S. F. Peterson, M. C. Mataya, D. K. Matlock   +2 more
openaire   +1 more source