Results 51 to 60 of about 822,229 (216)
Chemie Ingenieur Technik, EarlyView.This study explores the process chain for reverse engineering and additive manufacturing of a water pump impeller in a process plant. Key aspects include digital twin creation, CAD redesign, material certification, Hirtisation postprocessing, and performance testing. Insights highlight iterative design for improved precision and reliability.
Michael Stadler +3 more
wiley +1 more source
A constitutive model for analyzing martensite formation in austenitic steels deforming at high strain rates [PDF]
, 2012 This study presents a constitutive model for steels exhibiting SIMT, based on previous seminal works, and the corresponding methodology to estimate their parameters.
FERNANDEZ-SAEZ, José +5 more
core +1 more source
Journal of Materials Research and TechnologyStrengthening conventional materials through additive manufacturing is generally understood to occur due to rapid cooling in the metallurgical process, which refines the microstructure by producing smaller grain sizes and segregating elements at specific
Yurong Wang +5 more
doaj +1 more source
Analysis of Corrosion and Wall Perforation in the Heat Exchanger Made of AISI 316L Stainless Steel
Materials and Corrosion, EarlyView.Elevated passivation temperature is identified as the dominant factor triggering localized corrosion and subsequent perforation of AISI 316L heat exchanger tubes. Electrochemical and complementary characterization results show that the alloy retains high resistance to general, pitting, and intergranular corrosion, indicating that failure primarily ...
Bojana Radojković +7 more
wiley +1 more source
Development of a High- Chromium Ferritic Stainless Steel TTS443
Teshugang, 2012 In the light of specific properties of austenitic stainless steel 304 (type Crl8-Ni8) and ferritic stainless steel 430 (type Crl7), a high-chromium ferritic stainless steel TTS433 (/%: 0.010C, 21Cr, 0.40Cu, 0. 25Nb, 0. 20Ti, 0.
邹勇
doaj
Mechanical properties of pre-strained austenitic stainless steel from the view of energy density
Results in Physics, 2018 The effect of pre-strain on mechanical properties was investigated for 316L austenitic stainless steel over pre-strain value ranging from 0% to 35%. The effect of pre-strain on energy density of tensile curve was focused, and pre-strain enhances elastic ...
Jian Peng +3 more
doaj +1 more source
Fretting Wear and Corrosion Behavior of the Fe‐35Mn Biodegradable Alloy for Biomedical Applications
Materials and Corrosion, EarlyView.This study evaluates the corrosion and tribological wear behavior of the Fe‐35Mn alloy, demonstrating superior mechanical stability and a more favorable degradation rate than pure iron, thereby highlighting its potential for biomedical applications. ABSTRACT The biodegradable Fe‐35Mn alloy has emerged as a promising material for temporary implants due ...
Kerolene Barboza da Silva +7 more
wiley +1 more source
Materials and Corrosion, EarlyView.Hydrogen‐enhanced SCC of WAAM Inconel 625 in 3.5 wt.% NaCl solution. Hydrogen charging reduces passive film stability (lower corrosion potential) and promotes pitting at Laves phase/matrix interfaces. Stress corrosion cracks propagate along Laves‐rich regions, leading to quasi‐cleavage brittle fracture.
Xu Zhang +5 more
wiley +1 more source
Microstructural evolution of AISI304 stainless steel in the Steckel Mill rolling process [PDF]
, 2004 Includes bibliographical references (leaves [105]-110).The microstructural evolution of AISI304 stainless steel in the Steckel mill rolling process is investigated.
Parker, Sa-aadat
core +1 more source
MetalsHigh nitrogen austenitic stainless steels are an important engineering structural material. Under annealing conditions, the addition of interstitial solid solution element nitrogen can improve the yield strength and tensile strength of the alloy without ...
Yinghu Wang +5 more
doaj +1 more source