Results 101 to 110 of about 2,162 (214)

Hot centrifugal coating: A novel method for enhancing diffusion bonding integrity at steel-brass interfaces

Results in Surfaces and Interfaces
Steel cylinders are widely used in industry, but their service life is often limited by corrosion and wear. Conventional coating methods generally produce only mechanical bonds and can lead to delamination and interfacial failure.
Jamiatul Akmal, Heri Rustamaji, Martinus, Nurcahya Nugraha, Selviana Larasati   +4 more
doaj   +1 more source

Caracterización de la capa de boruros formada durante la austenización de un hierro nodular austemperizado//Characterization of borides coating formed during austenitization of an austempered ductile iron

Ingeniería Mecánica, 2015
En este trabajo se ha investigado el efecto de la austenitización y el borurado simultáneos, a 950 ºC, en la microestructura, la microdureza Vickers y el espesor de la capa borurada en medio líquido de un hierro nodular austemperizado no aleado.
Urbano Ordóñez‐Hernández, Sarah Parada-de-la-Puente, Carlos Figueroa-Hernández, Francisco-J. Mondelo-García, Arturo Barba-Pingarrón, Alfredo del-Castillo-Serpa   +5 more
doaj  

INFLUENCE OF STRUCTURAL STATE OF CARBON STEEL IN THE PROCESS OF AUSTENITE APPEARING DURING REHEATING DOUBLE-PHASE (A+Y) FIELD

Nauka ta progres transportu, 2010
Based on the analysis of research results for the kinetics of austenitization process the order of the original structures in the direction of increasing the rate of austenite formation is determined.
B. I. Kindratskyi, S. O. Yakovliev, I. E. Kramar, O. I. Shaptala   +3 more
doaj  

Influence of austenitization conditions of OTV1D steel on martensitic transformation

V okviru magistrskega dela smo raziskovali vpliv pogojev avstenitizacije, tj. temperature in časa, na martenzitno transformacijo v orodnem jeklu OTV1D za izdelavo valjev za hladno valjanje.
Založnik, Žan
core  

Crystallographic relations of cementite–austenite–ferrite in the diffusive decomposition of austenite

Bulletin of Prydniprovs’ka State Academy of Civil Engineering and Architecture, 2016
Проведено пошук нових, більш точних орієнтацій них співвідношень між кристалічними решітками в перлітних і бейнітних продуктах розпаду аустеніту. Методика. Використано методи: трансмісійної електронної мікроскопії, мікродифракції, математичного матричного і стереографічного аналізів.
Bolshakov, V. I., Sukhomlin, G. D., Sukhomlin, V. I.   +2 more
openaire   +1 more source

Targeted Optimization of Mechanical Properties in Pearlitic Steel via Tailored Heat Treatment: The Role of Austenitization and Isothermal Quenching Parameters

To address the limitations of conventional single heat treatment parameter optimization in regulating the mechanical properties of pearlitic steels, this study aims to establish a tailored heat treatment framework by coupling ...
Shuqian Xie, Yuxiu Li, Ling Xu, Jinhua Zhou, Xiaowei Yin, Lin Wang, Bohao Chen   +6 more
core   +1 more source

Analysis of Fatigue Property of the Aviation Gear Steel 15Cr14Co12Mo5Ni2 During High-Temperature Carburizing and Quenching. [PDF]

Materials (Basel)
Feng W, Zhou Y, Zhang Y, Wang R, Zhao X.
europepmc   +1 more source

A critical review of chemical heterogeneity-driven microstructure control in steels. [PDF]

Appl Microsc
Lee SH, Kim JH.
europepmc   +1 more source

Decarburization Control of H13 Steel Under Varying Process Pressures During Austenitization. [PDF]

Materials (Basel)
Kwon GH, Choi B, Choi SY, An KJ, Moon KI.   +4 more
europepmc   +1 more source

Effect of Austempering on the Microstructure, Mechanical Properties and Tribological Performance of EN-GJS-800-8 Ductile Iron Castings. [PDF]

Materials (Basel)
Jaroszek J, Miko E, Nowakowski Ł, Zaczyński A.   +3 more
europepmc   +1 more source