Results 81 to 90 of about 1,520 (193)
Optimization of Input Parameters of AWJM: Using Three Different Abrasives on MS2062
Non-Metallic Material Science, 2019 The objective of this work is to optimize input parameters of AWJM (Abrasive Water Jet Machining) such as Nozzle Transverse Speed (NTS), Abrasive Flow Rate (AFR) and Stand-off Distance (SOD) using three different abrasives Garnet, Brown Fused Alumina and White Aluminum Oxide on MS2062 and to compare their performance with surface finish, MRR and kerf ...
Kusnurkar S. V +1 more
openaire +1 more source
Leukocyte and bacteria imaging in prosthetic joint infection [PDF]
European Cells & Materials, 2013 There has been a significant increase in the number of joint prosthesis replacements worldwide. Although relatively uncommon, complications can occur with the most serious being an infection.
AWJM Glaudemans +3 more
doaj
Surface Hardening by Technology Hydroabrasive Jet and its Technological Modifications [PDF]
, 2014 Import 05/08/2014Bakalářská práce se zaměřuje na studium hydroabrazivního vodního paprsku a jeho stručným popisem zařízení. Tato práce se také dále zabývá studiem zpevňování povrchů různými strojírenskými technologiemi a nekonvenční metodou vodního ...
Koniuch, Michal
core
European Journal of Heart Failure, Volume 26, Issue 3, Page 695-698, March 2024.
Alwin Tubben +13 more
wiley +1 more source
Optimizing Abrasive Water Jet Machining Parameters on Cutting Hybrid Metal Matrix Composites Al7075 by Genetic Algorithm [PDF]
, 2020 Hybrid Metal Matrix Composites (MMC) Al7075 is a difficult-to-cut material that required non-conventional machining to manufacture automotive, aerospace, and defence components. The composite with minimum Bottom Kerf Width is much desire than minimum Top
Mohd Hashim, Saipul Azmi Mohd Hashim +1 more
core +1 more source
WHS (Wound Healing Society) guidelines update: Diabetic foot ulcer treatment guidelines
Wound Repair and Regeneration, Volume 32, Issue 1, Page 34-46, January/February 2024.
Lawrence A. Lavery +7 more
wiley +1 more source
Application of Silicon Carbide in Abrasive Water Jet Machining [PDF]
, 2011 Silicon carbide (SiC) is a compound consisting of silicon and carbon. It is also known as carborundum. SiC is used as an abrasive material after it was mass produced in 1893. The credit of mass production of SiC goes to Edward Goodrich Acheson.
Ahsan Ali Khan, Mohammad Yeakub Ali
core +2 more sources
Journal of Natural FibersA significant portion of the material market is completely governed by the novel polymer composites, either reinforced with synthetic or natural fibers.
Venkatesh Chenrayan +11 more
doaj +1 more source
The promising role of dynamic 18F-NaF PET-CT in diagnosing symptomatic joint prosthesis [PDF]
, 2015 Our purpose was to establish proof of principle case study for the use of dynamic 18F-NaF PET-CT in the assessment of knee and hip prostheses. Approval was granted by the research ethics committee and informed consent was obtained.
Adesanya, Oludolapo +2 more
core
Journal of Natural Fibers, 2017 This work deals with the investigation of Abrasive Water Jet Machining (AWJM) on banana fiber reinforced polyester composite. The composite is prepared with 20 wt. % of fiber through hand layup method followed by compression molding.
V. Arumuga Prabu +2 more
doaj +1 more source