Results 51 to 60 of about 1,983 (184)

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, Volume 28, Issue 4, 18 February 2026.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Comparative study of dynamic recrystallization behavior, microstructural characteristics, and mechanical properties of high-speed-extruded AZ31 and BA56 magnesium alloys

Journal of Magnesium and Alloys
This study compares the microstructural evolution, dynamic recrystallization (DRX) behavior, tensile properties, and age-hardenability between the newly developed high-speed-extrudable BA56 alloy and those of the widely recognized AZ31 alloy in industry.
Gun Woong An, Sang-Cheol Jin, Taekyung Lee, Sumi Jo, Sung Hyuk Park   +4 more
doaj   +1 more source

Cold-Rolling Effect on Low-Frequency Damping Properties of AZ31 Magnesium Alloy Plate at Moderately High Temperature [PDF]

Archives of Metallurgy and Materials
This study investigated the influence of cold-rolling on the damping capacity of the hot-extruded AZ31 alloy plate. The damping capacity of the hot-extruded and the cold-rolled AZ31 alloy plates were measured by a dynamic mechanical analysis with a ...
Shih-Hang Chang
doaj   +1 more source

Fretting wear in AZ31 magnesium alloy

Transactions of the JSME (in Japanese), 2016
Fretting wear in magnesium alloy AZ31 was investigated in order to understand the fundamental tribological properties in magnesium alloy. Ball on disc type fretting test was conducted, in which the cyclic tangential force was applied by rotating a gear pear with the weight.
Takefumi OTSU, Yasuo YOSHITAKE
openaire   +3 more sources

Loading Mode Dependence of Twin‐Twin Boundary Formation in a Textured Magnesium Alloy

Advanced Materials Interfaces, Volume 13, Issue 4, 17 February 2026.
The structures of twin‐twin boundaries formed by interactions between twin variants sharing the same or different zone axes in a deformed magnesium alloy are demonstrated. Lattice distortion around complicated interfaces promotes grain refinement in the subsequent thermomechanical process, enhancing the mechanical performance of magnesium alloys ...
Yuzhi Zhu, Shiqiang Wang, Yi Chen, Guanyi Wang, Yinhu Zhao, Zidong Wang, Zhipeng Li, Dewen Hou   +7 more
wiley   +1 more source

Deformation modes and anisotropy in magnesium alloy AZ31 [PDF]

International Journal of Materials Research, 2009
Abstract A strongly textured sheet of magnesium alloy AZ31 has been subjected to tensile testing at temperatures between ambient and 300 °C. Structures have been examined by optical and transmission electron microscopy and also by atomic force microscopy to quantify surface displacements seen at grain boundaries.
Bevis Hutchinson, Matthew R. Barnett, Alireza Ghaderi, Pavel Cizek, Ilchat Sabirov   +4 more
openaire   +1 more source

Finite Element‐Based Wear Prediction Using Archard's Law for Single Mobility Bearing of Total Hip Prosthesis During Walking: A Literature Review

Engineering Reports, Volume 8, Issue 2, February 2026.
This review provides a comprehensive and critical evaluation of computational wear prediction studies in total hip prostheses, with a specific focus on those employing Archard's wear law within finite element frameworks under walking conditions for single mobility bearing designs.
Muhammad Imam Ammarullah, Abdulfatah Abdu Yusuf, Mohamad Izzur Maula, M. Danny Pratama Lamura, Budi Setiyana, Mohammad Tauviqirrahman, Athanasius Priharyoto Bayuseno, Jamari Jamari, Muhammad Hanif Ramlee   +8 more
wiley   +1 more source

Preparation and Characterization of Aminated Hydroxyethyl Cellulose-Induced Biomimetic Hydroxyapatite Coatings on the AZ31 Magnesium Alloy

Metals, 2017
The purpose of this work is to improve the cytocompatibility and corrosion resistance of magnesium alloy in the hope of preparing a biodegradable medical material.
Bowu Zhu, Yimeng Xu, Jing Sun, Lei Yang, Changgang Guo, Jun Liang, Baocheng Cao   +6 more
doaj   +1 more source

Microstructure Evolution and Mechanical Properties of AZ31 Magnesium Alloy Sheets Prepared by Low-Speed Extrusion with Different Temperature

Crystals, 2020
AZ31 magnesium alloy sheets were prepared by low-speed extrusion at different temperatures, i.e., 350 °C, 400 °C, and 450 °C. The microstructure evolution and mechanical properties of extruded AZ31 magnesium alloy sheets were studied.
Wenyan Zhang, Hua Zhang, Lifei Wang, Jianfeng Fan, Xia Li, Lilong Zhu, Shuying Chen, Hans Jørgen Roven, Shangzhou Zhang   +8 more
doaj   +1 more source

Designing High‐Strength and High‐Ductility Cast Mg–Zn–Al–Mn–Sn Alloys via τ‐Mg32(Al,Zn)49 Phase Tuning and Twin Boundary Toughening Optimisation

Rare Metals, Volume 45, Issue 2, February 2026.
ABSTRACT Achieving a simultaneous enhancement of strength and ductility remains a critical bottleneck for the large‐scale and cost‐effective engineering application of magnesium alloys. In this work, guided by first‐principles calculations, we tailored the τ‐Mg32(Al,Zn)49 phase and optimised twin boundary, thereby designing and successfully ...
Yun‐Xuan Zhou, Wen‐Jun Tian, Hao Lv, Quan Dong, Hong Yang, Pu‐Hua Yu, Jun Tan, Xian‐Hua Chen, Fu‐Sheng Pan   +8 more
wiley   +1 more source