Results 41 to 50 of about 735,720 (116)
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen +3 more
wiley +1 more source
As the lightest structural metal material, magnesium alloy has the potential to replace aluminum alloy and steel parts, but its development is limited by problems such as poor plasticity, processing difficulties, and casting defects.
Min Zhang +3 more
doaj +1 more source
Process Mechanics and Surface Integrity Induced by Dry and Cryogenic Machining of AZ31B-O Magnesium Alloy [PDF]
The corrosion resistance of magnesium alloys depends mainly on its surface integrity. Previous experimental studies have shown that machining can induces small (nano-scale) grain size, compressive residual stresses and basal plane crystallographic ...
GERMAIN, Guénaël +12 more
core +1 more source
This review highlights recent advancements in Severe Plastic Deformation (SPD) techniques tailored for tubular samples. The mechanisms of processing are critically discussed with emphasis on microstructural control and the governing process parameters that enable refinement to ultrafine‐ and nano‐grained structures. Comparative insights into equivalent
Eman M. Zayed +5 more
wiley +1 more source
This study introduces a dual‐stage language model framework that extracts processing information from scientific literature and integrates it with thermodynamic data for magnesium alloy design. By combining semantic intelligence with quantitative modeling, the approach enables processing‐aware prediction of mechanical and thermal properties, bridging ...
Ziliang Lu +8 more
wiley +1 more source
Effects of Erbium Addition on the Corrosion Resistance and Microstructure of AZ91 Magnesium Alloy
The microstructures and corrosion resistance of AZ91 and AZ91+0.5 wt.% erbium (Er) magnesium alloys were studied, respectively. The results show that the Er addition in scrap AZ91 magnesium alloy can improve the corrosion resistance, markedly.
Yang Xu, Jing Zhu, Zhong Jun Wang
core +1 more source
Influence of annealing and spheroidizing treatment on microstructure and mechanical properties of AZ91 magnesium alloy [PDF]
The low-strength and high-brittleness of AZ91 cast magnesium alloy mainly result from the coarse divorced eutectic phase. To solve these problems, the annealing treatment of AZ91 cast magnesium alloy was carried out at 415 ℃ and held for 24 h in this ...
Zhang Jumei, Wang Zhihu, Jiang Bailing
doaj
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Hydroxyapatite (HA)-graphene oxide (GO) composite coatings reinforced with various rare earth (RE) metal oxide (La2O3 and Y2O3) of composite coatings are electrophoretic deposited on AZ91 magnesium alloy substrate.
Qimin Liang +3 more
doaj +1 more source
New Advances of Degradable Magnesium‐Based Metal Biomaterials in the Field of Orthopedics
ABSTRACT Based on their outstanding biomechanical properties and superior osteogenic activity, magnesium (Mg) and its alloys have been extensively investigated for their biocompatibility and therapeutic efficacy in treating fractures and bone defects.
Jia‐Nan Yu +8 more
wiley +1 more source

