Results 11 to 20 of about 168,607 (257)
Positive‐Tone Nanolithography of Antimony Trisulfide with Femtosecond Laser Wet‐Etching
Advanced Functional Materials, EarlyView.A butyldithiocarbamic acid (BDCA) etchant is used to fabricate various micro‐ and nanoscale structures on amorphous antimony trisulfide (a‐Sb2S3) thin film via femtosecond laser etching. Numerical analysis and experimental results elucidate the patterning mechanism on gold (reflective) and quartz (transmissive) substrates.
Abhrodeep Dey +12 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Trap state engineering in inverted organic photodetectors (OPDs) is achieved via combined layer‐by‐layer (LbL) processing and poly(N‐vinylcarbazole) (PVK) incorporation. LbL reduces the trap density while PVK additives gradually shift trap states from shallow band‐edge to deep mid‐gap levels, tailoring the energy distribution.
Jingwei Yi +10 more
wiley +1 more source
Advanced Functional Materials, EarlyView.This study advances our understanding of aortic valve stenosis by capturing spatially resolved chemical and structural changes at the nanoscale. The findings highlight the potential of combined Raman and electron microscopy for understanding calcification mechanisms across diverse tissue types.
Robin H. M. Van der Meijden +11 more
wiley +1 more source
Advanced Functional Materials, EarlyView.An efficient NiOx HTL is successfully prepared by introducing MXene as an additive without further surface modification to fabricate high‐performance FASn0.5Pb0.5I3 perovskite solar cells. The introduction of MXene contributes to improved conductivity of NiOx, better aligned at NiOx/perovskite interfaces, and enhanced quality of perovskite films ...
Lijun Chen +12 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Conventional unstable electron transport layers (ETLs) limit self‐powered organic sensors. This work resolves this by developing a n‐type self‐assembled monolayer (SAM), “3‐PAPh”. This SAM forms a chemically stable and structurally ordered interface that fundamentally suppresses defect formation.
Ohhyun Kwon +11 more
wiley +1 more source
Structural Porosity and Low Mineral Density in Enamel Rods Drive Molar Incisor Hypomineralisation
Advanced Functional Materials, EarlyView.This study uses advanced imaging modalities on multiple length scales to show that molar‐incisor hypomineralization does not present as a locally homogeneous pathology. Instead, microstructural defects, characterized through non‐mineralized, protein‐rich sheaths and an altered mineral structure in between prism rods, resulting in local differences in ...
Katharina Jähn‐Rickert +14 more
wiley +1 more source
Digital Actuation Control of Soft Robotic Origami With Self‐Folding Liquid Crystal Elastomer Hinges
Advanced Functional Materials, EarlyView.Self‐folding soft‐rigid hybrid robotic origami is enabled by liquid crystal elastomer actuators with embedded Joule heating and closed‐loop digital control. Digitally addressable hinges provide reversible and programmable transitions between distinct folded states while maintaining actuation performance at high cycle counts (over 1500).
David C. Bershadsky +3 more
wiley +1 more source
Imaging of Biphoton States: Fundamentals and Applications
Advanced Functional Materials, EarlyView.Quantum states of two photons exhibit a rich polarization and spatial structure, which provides a fundamental resource of strongly correlated and entangled states. This review analyzes the physics of these intriguing properties and explores the various techniques and technologies available to measure them, including the state of the art of their ...
Alessio D'Errico, Ebrahim Karimi
wiley +1 more source
Ultra Wide Swath Imaging With Multi-Channel SAR Systems [PDF]
, 2008 Multi-channel radar systems allow for overcoming the inherent limitation of conventional synthetic aperture radar (SAR). An example is the combination of digital beamforming on receive in elevation with multi-aperture SAR signal reconstruction in azimuth
Bordoni, Federica +4 more
core
Advanced Functional Materials, EarlyView.A Cu‐based crystal‐glass composite with high‐density twins is identified by a fast screening technique using combinatorial sputtering together with XRD and nanoindentation mapping. This bamboo‐like structure demonstrates homogenous plastic flow and retains high strength during in situ high temperature tests, up to 1 GPa at 550°C, owing to those ...
Chunhua Tian +10 more
wiley +1 more source