Results 21 to 30 of about 30,042 (212)
Arthritis Care &Research, EarlyView.Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan +10 more
wiley +1 more source
A Study on Wear and Friction of Passenger Vehicles Control Arm Ball Joints
Energies, 2021 The following paper describes research on vehicle suspension elements: the ball joints. The worn surface roughness of selected ball pins and their bearings was compared in terms of vehicle mileage, utilization period, and car model.
Marek Wozniak +3 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
A Dynamic Analysis of a Flexible Rotor in Ball Bearings with Nonlinear Stiffness Characteristics
International Journal of Rotating Machinery, 1997 This paper presents an effective analysis approach for a flexible rotor in ball bearings with nonlinear stiffness characteristics to obtain realistic dynamic behavior results.
Dong-Soo Lee, Dong-Hoon Choi
doaj +1 more source
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
CHARACTERISTIC STUDY FOR THE HETEROGENEOUS ROLLING BEARING MATCH WAY
Jixie qiangdu, 2015 When angular contact ball bearings match together,due to high demand of manufacturing and installation precision,only increasing the number of angular contact ball bearings to increase the radial bearing capacity has great limitations.Therefore,it was ...
WU KaiSong, DENG Tao, CAI Can, FENG Yan
doaj
LubricantsThe double-piece inner ring ball bearing is an important part of an aero-engine. An excessive bearing temperature leads to bearing thermal expansion, lubricating oil performance degradation, and other problems that seriously affect the service life and ...
Yujun Xue +3 more
doaj +1 more source