Results 31 to 40 of about 885,311 (296)
Scale up and simulation of Vertimill™ pilot test operated with copper ore
Journal of Materials Research and Technology, 2014 Vertimill™ has been used in regrind circuits during the past years due to its greater efficiency when compared to the conventional tube ball mill. This paper presents the Vertimill™ pilot grinding tests with a sample of copper ore carried out in closed ...
Douglas Batista Mazzinghy +3 more
doaj +1 more source
Modeling Impulsive Ball Mill Forces Effects on the Dynamic Behavior of a Single-Stage Gearbox
Machines, 2022 Gearboxes are frequently used in the mining industry, especially for power transmission between the electric drive and the ball mill; besides the extreme complexity of a ball mill gear transmission system, the fault diagnosis by vibration analysis can be
Gauthier Ngandu Kalala +4 more
doaj +1 more source
Comparison of dark and milk cocoa toppings produced by a five-roll mill and a ball mill [PDF]
Food and Feed ResearchChocolate toppings are confectionery products comprised of non-fat dark cocoa solids and sugar particles dispersed in cocoa butter, as a continual matrix.
Stožinić Milica +6 more
doaj +1 more source
The Mechanism and Grinding Limit of Planetary Ball Milling [Translated]†
KONA Powder and Particle Journal, 2014 To clarify the mechanism and characteristics of planetary ball milling, batch grinding experiments were carried out under various conditions.
Qian-Qiu Zhao +2 more
doaj +1 more source
Rekayasa MesinResearch has been conducted on the effect of Zirconia Ball on the volume of Mill Jar in the process of smoothing Alumina ceramic powder with Horizontal Ball Mill tool.
Ade Indra +2 more
doaj +1 more source
Hyperchaotic qualities of the ball motion in a ball milling device
Chaos: An Interdisciplinary Journal of Nonlinear Science, 1999 Ball collisions in milling devices are governed by complex dynamics ruled by impredictable impulsive forces. In this paper, nonlinear dynamics techniques are employed to analyze the time series describing the trajectory of a milling ball in an empty container obtained from a numerical model.
C. CARAVATI +3 more
openaire +4 more sources
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
The Characteristics of Comminution with High Pressure Roller Mills
KONA Powder and Particle Journal, 2014 High pressure roller mills have been used successfully for grinding brittle materials since 1985. The advantages of this new technology are, less energy consumption, less wear and noise emission and a smaller mill ...
Klaus Schönert
doaj +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source