Results 111 to 120 of about 63,659 (281)

Anisotropy Thermal Properties of Electrically Insulating Thin Films and Sheets: A Review

Small Methods, EarlyView.
Thermally conducting and electrically insulating materials with anisotropy properties play an integral role in advanced thermal management, in particular for electronic devices. This review discusses recent progress in enhancing thermal conductivity and controlling the thermal anisotropy between in‐plane and cross‐plane (through‐thickness) directions ...
Shanmukhi Sripada, Cole R. Davis, Aalok U. Gaitonde, Amy M. Marconnet   +3 more
wiley   +1 more source

Comparison of the properties of synthetic and animal ballistic gelatine in forensic investigations = Porównanie właściwości syntetycznej i zwierzęcej żelatyny balistycznej w badaniach kryminalistycznych

Archives of Forensic Medicine and Criminology
Introduction: Ballistic gelatine is widely used as a medium for simulating human tissue in ballistic research.
Grzegorz Motrycz, Karolina Julia Helnarska   +1 more
doaj   +1 more source

Programmable Porosity in Polymers via Microfluidic Templating and 3D Printing

Small Methods, EarlyView.
Fluid templating is a powerful way to produce porous polymers. Microfluidic technologies enable fine control over the dimension and packing of bubbles and droplets. Combined with additive manufacturing, microfluidic templating enables the creation of polymeric functionally graded porous materials in which both porosity and three‐dimensional geometry ...
Federico Serpe, Roberta Angelini, Andrea Barbetta, Vanessa Rosciardi   +3 more
wiley   +1 more source

Reverse design of solid propellant grain based on deep learning: Imaging internal ballistic data

Defence Technology
The reverse design of solid rocket motor (SRM) propellant grain involves determining the grain geometry to closely match a predefined internal ballistic curve. While existing reverse design methods are feasible, they often face challenges such as lengthy
Lin Sun, Xiangyu Peng, Yang Liu, Shu Long, Weihua Hui, Ran Wei, Futing Bao   +6 more
doaj   +1 more source

Inconsistency in 9 mm bullets : correlation of jacket thickness to post-impact geometry measured with non-destructive X-ray computed tomography [PDF]

, 2014
Fundamental to any ballistic armour standard is the reference projectile to be defeated. Typically, for certification purposes, a consistent and symmetrical bullet geometry is assumed, however variations in bullet jacket dimensions can have far reaching ...
Landheer, D., Thornby, J. A., Williams, M. A., Attridge, A., Williams, T., Barnes-Warden, J., Fenne, P., Norman, D. G.   +7 more
core  

Crash Behavior of DP800–DP1000 Advanced High‐Strength Steel’s Dissimilar Resistance Spot Welded Joints Under Quasi‐static and High Strain Rates

steel research international, EarlyView.
The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley   +1 more source

Effect of Different Surface Treatments on Resistance to Abrasive Wear of AISI 4140 Steel

steel research international, EarlyView.
This study investigates how different surface treatments affect resistance to abrasive wear of AISI 4140 Steel. The wear rate was significantly higher in samples subjected to conventional treatments than in samples coated using the HVOF process, demonstrating the superior efficiency of coatings applied by thermal spraying in mitigating abrasive wear ...
Everton Freitas de Oliveira, Tomasz Trzepieciński, Valmir Dias Luiz, Jorge Luis Coleti   +3 more
wiley   +1 more source

A NUMERICAL MODEL FOR BALLISTIC IMPACT RESPONSE OF COMPOSITE ARMORS

Havacılık ve Uzay Teknolojileri Dergisi, 2018
In this study, we present a numerical model to simulate the ballistic impact of a rigid right circular cylinder (RCC) projectile into a woven fabric target.
Demet Balkan, Seher EKEN
doaj  

Research on ballistic performance of green shear thickening functionalized fabric based on solid waste modification

Materials & Design
Based on the solid waste-based modification, green shear-thickening functionalized ballistic composites were prepared. Silica aerosols were obtained from solid waste diatomaceous earth through sol–gel preparation, gel aging, and supercritical drying. The
Ke Yan, Hao Wu, Shaobo Qi, Xingyu Shen, Runhan Li, Xing Li, Haoshi Sun, Mengqi Yuan   +7 more
doaj   +1 more source

The Reflexive Turn in Systems Engineering: A Disciplinary Response to Complexity

Systems Engineering, EarlyView.
ABSTRACT The Future of Systems Engineering (FuSE) programme has called for the discipline to evolve as a transdiscipline capable of engaging complex eco‐socio‐technical challenges. Yet the pace of that evolution has been slower than the arguments for it would predict. This article examines why.
Raul Leal Ascencio
wiley   +1 more source