Results 91 to 100 of about 8,800,730 (192)

HSPICE implementation of a numerically efficient model of CNT transistor

This paper presents the algorithms of an implementation of a numerically efficient carbon nanotube transistor (CNT) model in HSPICE. The model is derived from cubic spline non-linear approximation of the non-equilibrium mobile charge density.
Zhou, Dafeng, Kazmierski, Tom, Al-Hashimi, Bashir   +2 more
core   +1 more source

Analytic ballistic performance model of whipple shields

, 2015
Analytic ballistic performance model of whipple ...
MD Bjorkman (15814658), JE Miller (14470608), Shannon Ryan (13092264), EL Christiansen (15814661)   +3 more
core  

Inconsistency in 9 mm bullets : correlation of jacket thickness to post-impact geometry measured with non-destructive X-ray computed tomography [PDF]

, 2014
Fundamental to any ballistic armour standard is the reference projectile to be defeated. Typically, for certification purposes, a consistent and symmetrical bullet geometry is assumed, however variations in bullet jacket dimensions can have far reaching ...
Landheer, D., Thornby, J. A., Williams, M. A., Attridge, A., Williams, T., Barnes-Warden, J., Fenne, P., Norman, D. G.   +7 more
core  

Research on the creation of new UD laminates and its ballistic performance using CSC aramid yarns via experiment and FEA analysis

Journal of Industrial Textiles
In this paper, a new type of core-spun compound aramid yarn has been applied in the construction of UD fabric to investigate if the ballistic performance of the whole fabric could be positively influenced.
Dan Yang, Kai Zhu, Shengdong Liu, Fan Fei, Jinchun Li, Xiaogang Chen   +5 more
doaj   +1 more source

Ballistic Limit of High-Strength Steel and Al7075-T6 Multi-Layered Plates Under 7.62-mm Armour Piercing Projectile Impact

Latin American Journal of Solids and Structures
This paper presents the computational-based ballistic limit of laminated metal panels comprised of high strength steel and aluminium alloy Al7075-T6 plate at different thickness combinations to necessitate the weight reduction of existing armour steel ...
N. A. Rahman, S. Abdullah, W. F. H. Zamri, M. F. Abdullah, M. Z. Omar, Z. Sajuri   +5 more
doaj   +1 more source

Three-Dimensional Smooth Particle Hydrodynamics Modeling and Experimental Analysis of the Ballistic Performance of Steel-Based FML Targets. [PDF]

Materials (Basel), 2022
Kubit A, Trzepieciński T, Kiciński R, Jurczak K.   +3 more
europepmc   +1 more source

A comparison of three post-activation potentiation enhancement warm up strategies on bench press performance

Frontiers in Sports and Active Living
BackgroundAt loads greater than 80% of one repetition maximum in bench press, at the ascending phase of the movement, the barbell decelerates or stops for a short time before it accelerates again during a region named sticking region.
Yousef Hedayati, Roland van den Tillaar
doaj   +1 more source

A hybrid approach of NiP coating and STF impregnation of UHMWPE fabric for conductive soft body armor

Journal of Materials Research and Technology
To enhance the ballistic impact performance and impart electrical conductivity into soft armor material made up of UHMWPE fabric, a novel hybrid technique has been devised and incorporated.
Anand Biradar, S. Arulvel, Jayakrishna Kandasamy   +2 more
doaj   +1 more source

Ballistic performance of Polycarbonate and Polymethyl methacrylate under normal and inclined dynamic impacts. [PDF]

Heliyon, 2021
Sadeghi Esfahlani S.
europepmc   +1 more source

Ballistic Performance of Guaruman Fiber Composites in Multilayered Armor System and as Single Target. [PDF]

Polymers (Basel), 2021
Reis RHM, Nunes LF, da Luz FS, Candido VS, da Silva ACR, Monteiro SN.   +5 more
europepmc   +1 more source