Results 61 to 70 of about 10,762 (232)

IDENTIFICATION OF SCIENCE-PHYSICS CONCEPTS IN THE TRADITIONAL GAME OF BAMBU GILA AND ITS IMPLEMENTATION IN LEARNING

open access: yesEDU SCIENCES JOURNAL, 2023
Local wisdom is ideas, thoughts, values, and views that are wise, valuable, inherent, and adhered to by the local community. It is typical of an area regarding cultural, economic, communication, and ecological aspects, as well as the attitudes that are ...
Anatasija Limba   +4 more
semanticscholar   +1 more source

SIFAT FISIS DAN PENGERINGAN LIMA JENIS BAMBU

open access: yesJurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017
Informasi mengenai sifat fisis bambu penting untuk memahami kestabilan dimensi bambu, sedangkan informasi tentang sifat pengeringan dibutuhkan sebagai dasar untuk menetapkan suhu optimum pengeringannya.
Efrida Basri, Rohmah Pari
doaj   +1 more source

Cooptimized Sensing and Sole Mechanics Enable Embodied‐Intelligence Design of User‐Specific Smart Footwear

open access: yesAdvanced Intelligent Systems, EarlyView.
An embodied codesign framework for smart footwear is presented, jointly tuning lattice mechanics and sensing for personalized plantar pressure monitoring. By integrating pneumatic sensing within 3D‐printed lattice soles, the system achieves accurate real‐time centre‐of‐pressure tracking with reduced sensor count and energy demand, demonstrating how ...
Fengyu Zhong   +3 more
wiley   +1 more source

Conservação do bambu [PDF]

open access: yesAnais da Escola Superior de Agricultura Luiz de Queiroz, 1958
This paper brings to light new data on the absence of influence of lunar phases on the preservation of bamboo sticks. The author cut down for one and a half years (from - June 18, 1947 to December 30,1948) bamboos in every phase of the moon. With part of the sticks obtained a fence was built; the rest v/as kept under shelter. In the fence there were: 5
openaire   +3 more sources

TEKNOLOGI PENGOLAHAN DAN MANFAAT BAMBU

open access: yesJurnal Riset Industri Hasil Hutan, 2015
Bambu  di Indonesia potensinya  sangat menjanjikan untuk dimanfaatkan dengan baik, bambu  merupakan tumbuhan mudah dikembangkan dan mempunyai daur hidup yang relatif cepat, dengan waktu panen hanya 3 – 4 tahun.
Effendi Arsad
doaj   +1 more source

PENGARUH PENGERINGAN TERHADAP PERUBAHAN WARNA, PENYUSUTAN TEBAL, DAN PENGURANGAN BERAT EMPAT JENIS BAMBU

open access: yesJurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2020
Warna permukaan batang bambu berubah secara alami akibat kondisi disekitarnya. Tulisan ini mempelajari perubahan warna permukaan bambu akibat pengeringan dalam ruangan (KU) dan dalam oven (KO).
Adik Bahanawan, Krisdianto Sugiyanto
doaj   +1 more source

How I Do It: Two Novel, Low‐Cost Phonomicrosurgery Models With Open‐Source, 3D‐Printed Laryngoscopes

open access: yesThe Laryngoscope, EarlyView.
Two new vocal fold microflap models using products found in any grocery store have been developed along with publicly available 3D‐printable parts for simulating multiple laryngoscopes commonly used during laryngeal phonomicrosurgery. This represents a low cost, easily reproducible model for basic laryngeal phonomicrosurgery training.
Sapir Pinhas   +3 more
wiley   +1 more source

Penggunaan Serat Bambu sebagai Bahan Tambah Pada Beton

open access: yesJurnal ilmiah ecosystem
Tujuan penelitian ini adalah untuk mengetahui pengaruh penambahan serat bambu terhadap beton normal. Metode penelitian yang digunakan adalah jenis kuantitatif dengan eksperimen tentang penggunaan serat bambu sebagai bahan tambah pada pembuatan beton ...
Kartina Kartina   +2 more
semanticscholar   +1 more source

STUDI PENGERINGAN BAMBU DENGAN PEMANFAATAN GAS BUANG ( FLUE GAS ) PEMBAKARAN GERABAH

open access: yesJurnal Ilmiah Rekayasa Pertanian dan Biosistem, 2019
Suhu gas buang dari hasil pembakaran gerabah relatif masih tinggi, suhunya masih sekitar 200oC. Gas buang hasil pembakaran gerabah ini diharapkan bisa dimanfaatkan sebagai media pengering, misalnya untuk mengeringkan bambu.
Taufikul Hadi   +2 more
doaj   +1 more source

The Influence of Infill on the Tensile Strength of some Mini‐Test Specimens Manufactured by 3D Printing From PLA

open access: yesMacromolecular Symposia, EarlyView.
ABSTRACT In industrial practice, situations may be encountered where small parts manufactured by 3D printing from polymeric materials are subjected to tensile stresses. Since standard tensile testing machines are not recommended for performing tests for values less than 10% of the machine's maximum nominal force, it is necessary to design and build a ...
Vlada Țisari   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy