Results 251 to 260 of about 389,775 (338)
Some of the next articles are maybe not open access.

Human voice filtering with band-stop filter design in MATLAB

2017 International Conference on Broadband Communication, Wireless Sensors and Powering (BCWSP), 2017
This paper discusses human voice filtering. The filtering was done by attenuating human voice's frequencies within a song's frequencies using filter design. Band-stop filter design is one of filter design that is used in this research. The band-stop filter design uses one type of windowing that is the Butterworth windowing.
Wulan Meiniar   +4 more
openaire   +2 more sources

Development of Reconfigurable Band Stop Filter Using Metamaterial for WLAN Application

Progress in Electromagnetics Research Symposium, 2022
In Wireless communication system microwave filter is most important device for pass the required band and reject the unwanted frequency. Metamaterial having important property to drastically change the electrical property parameter with reduction in size.
Khyati Chavda, A. Sarvaiya
semanticscholar   +1 more source

Tunable terahertz band-stop filter using strongly coupled split ring resonators integrated with on-chip waveguide

Journal of Applied Physics, 2021
We have used finite-element methods to design and simulate a tunable terahertz frequency range band-stop filter based on coupled split-ring resonators integrated into planar Goubau-line waveguide.
R. Parker-Jervis   +2 more
semanticscholar   +1 more source

Ultra-flat optical frequency comb generation based on a polarization modulator and a Butterworth band-stop filter.

Applied Optics, 2021
A new, to the best of our knowledge, scheme for the generation of ultra-flat optical frequency combs (OFCs) is proposed, which mainly uses a polarization modulator (PolM) and a first-order Butterworth band-stop filter.
Yi Guo, Y. Liu, Dan Li, Shibao Wu
semanticscholar   +1 more source

Electronically tunable band-stop filter

1988., IEEE MTT-S International Microwave Symposium Digest, 2003
The design procedures for an electronically tuned band-stop filter are presented. A technique for realizing tunable band-stop filters with coupled lines is discussed. The physical design and electrical performance of a five-section band-stop filter tunable from 6.5 GHz to 10 GHz, with a constant bandwidth, is given.
D. Auffray, J.L. Lacombe
openaire   +1 more source

Micromachined Spurline Band-stop Filter

2007 IEEE International Workshop on Radio-Frequency Integration Technology, 2007
This paper reports the design and fabrication of a membrane-supported spurline band-stop filter. The filter was fabricated using silicon bulk micromachining technique and a CMOS compatible metal/dielectric deposition RF sputtering technique. A closed-form expression of an equivalent value of dielectric constant is also derived and introduced to account
Preeti Sharma   +2 more
openaire   +1 more source

Cooperative band-stop filters

Optik, 2020
Abstract We analyze light transmission both through a 1D waveguide that has a regular array of atoms inside, and through a stack of equally-spaced partially reflecting mirrors. We view the atoms and mirrors as linear filters. As such, they have two inputs, light coming in from both sides, and two outputs, light going out to both sides.
openaire   +1 more source

Tunable superconducting band-stop filters

1998 IEEE MTT-S International Microwave Symposium Digest (Cat. No.98CH36192), 2002
Electrically tunable notch filters based on bulk single crystal SrTiO/sub 3/ (STO) parallel-plate resonators with High Temperature Superconducting (HTS) electrodes are reported. The filters operate at temperatures below 90 K. The center frequency, located in the range 0.5-2.0 GHz, can be controlled with an applied voltage, in some cases more than 100%.
S.S. Gevorgian   +3 more
openaire   +1 more source

Home - About - Disclaimer - Privacy