Results 121 to 130 of about 777,364 (238)
Revisiting the synthesis of dimethyl carbonate from methanol and carbon dioxide
The Canadian Journal of Chemical Engineering, Volume 104, Issue 11, Page 5954-5978, November 2026.Abstract The process for producing dimethyl carbonate (DMC) from carbon dioxide (CO2) and methanol is explored in this article. It provides an overview of the thermodynamics involved in DMC synthesis, discussing the challenges and potential solutions. The article highlights the reported use of catalysts and dehydrating agents to improve DMC yield and ...
Diego Alexander Santos Araque +3 more
wiley +1 more source
Polymer Composites, Volume 47, Issue 20, Page 18176-18190, 20 October 2026.Amino‐silane treatment improves the basalt fiber–PA6 interface, enhancing composite performance. ABSTRACT Basalt fiber‐reinforced polymer (BFRP) composites have emerged as sustainable alternatives to glass fiber (GF) composites, but their performance is often controlled by the quality of the fiber–matrix adhesion.
Mohammad Mezbah Ul Hoque +3 more
wiley +1 more source
Quality Assessment of Melanocratic Basalt for Mineral Fiber Product, Southern Urals, Russia
, 2015 Basalt fibers have recently come into the spotlight due to their superior physical and chemical properties, which rank only below expensive carbon and silicon carbide fibers.
Pisciotta, A. +4 more
core +1 more source
Polymer Composites, Volume 47, Issue 20, Page 18791-18811, 20 October 2026.Schematic overview of the investigated laminate architectures and reinforcement strategies used to evaluate their effects on the bearing performance and failure behaviour of thick carbon fibre/epoxy laminates. ABSTRACT This study provides a unified experimental comparison of 11 joint configurations in thick (7–12 mm) vacuum‐infused CFRP laminates ...
Hasan Caglar +7 more
wiley +1 more source
Surface treatment of Basalt fiber for use in automotive composites
, 2020 Surface treatment of Basalt fiber for use in automotive ...
Minoo Naebe (13085016) +4 more
core
, 2018 Basalt/aramid hybrid fiber reinforced composite laminates were prepared to examine the effect of hybridization on Charpy impact behavior of aramid fiber reinforced composite laminates.
Bozkurt, Ömer Yavuz +2 more
core +1 more source
Polymer Composites, Volume 47, Issue 19, Page 17057-17075, 10 October 2026.Hole‐making strategy and machining parameters influence delamination and hole quality in S2‐glass and basalt FRP composites, which subsequently affet flexural performance. Improved hole integrity leads to enhanced structural performance during three‐point bending.
Sara Saeed Abdulrahman Eltahir +2 more
wiley +1 more source
Low-Velocity Impact Behavior of Carbon/Basalt Fiber-Reinforced Intra-ply Hybrid Composites
, 2018 The effect of hybridization on the low-velocity impact behavior of woven carbon/basalt fiber-reinforced intra-ply hybrid composites was investigated experimentally.
SHISHEVAN, Farzin Azimpour +3 more
core +1 more source
Polymer Composites, Volume 47, Issue 19, Page 17076-17090, 10 October 2026.Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia +4 more
wiley +1 more source
Polymer Composites, Volume 47, Issue 19, Page 17544-17562, 10 October 2026.Schematic summary of the drilling damage and microstructural degradation mechanisms in basalt fiber‐reinforced composites after acidic aging. ABSTRACT This study investigates the drilling performance and environmental durability of basalt fiber reinforced polymer (BRC) and halloysite nanotube (HNT) modified basalt nanocomposites (BRnC) exposed to ...
İbrahim Aslan +3 more
wiley +1 more source