Results 21 to 30 of about 2,616,861 (245)
Seismic performance of reinforced concrete interior beam-column joints with novel reinforcement detail [PDF]
, 2021 Horizontal stirrups are normally required in reinforced concrete (RC) beam-column joints (BCJs) for resisting shear forces in seismic design. For RC moment-resisting frames subjected to a high lateral load, a large number of stirrups are needed in joint ...
Li, Bo +3 more
core +1 more source
Bistable Networks Enable Complex Shape Changes. [PDF]
Adv Sci (Weinh)Transition‐controlled metamaterials are networks of bistable mechanical memory that store local binary states and express them as global shape change. By decoupling low‐force programming from high‐force holding, a single lattice is reconfigured into distinct 2D profiles and 3D surfaces without continuous actuation, enabling reusable morphing materials ...
Thomas S, Lipton J.
europepmc +2 more sources
Seismic behavior of non seismically designed eccentric reinforced concrete beam column joints
, 2021 Non seismically designed eccentric reinforced concrete beam column joints were extensively used in existing reinforced concrete frame buildings, which were found to be vulnerable to seismic action in many incidences.
Liu, Ying +5 more
core +1 more source
Study of cold formed steel beam column joint to resist lateral load [PDF]
MATEC Web of Conferences, 2019 Cold Formed Steel (CFS) is one of the materials that recently used in building structures. There are many advantages of CFS compared with other materials, such as lightweight, high tensile strength, and fast construction. Hollow Structural Sections (HSS)
Desmaliana Erma +3 more
doaj +1 more source
Case Studies in Construction Materials, 2021 This study aims to provide a review of the literature on the hybrid reinforced concrete beam-column joints that used steel fibers reinforced concrete (SFRC) or high-performance fibers reinforced cementitious composites (HPFRCC) in the joint region ...
Wissam Nadir +2 more
doaj +1 more source
EXPERIMENTAL STUDY OF RC EXTERIOR BEAM-COLUMN JOINT SUBJECTED TO TORSIONAL MOMENT [PDF]
Journal of Engineering Research - Egypt, 2015 This paper presents the results of an experimental program conducted in order to investigate the behavior of Type-I beam-column Joints, where the beam was subjected to shear stresses due to combined effect of shear force and torsional moment (beam ...
Tarek El-Shafiey +3 more
doaj +1 more source
Journal of Engineering, 2023 A reinforced concrete frame is referred as "RIGID FRAMES". However, researches indicate that the Beam-Column joint (BCJ) is definitely not rigid. In addition, extensive research shows that failure may occur at the joint instead of in the beam or the ...
Jamal A. Farhan, Zaid M. Kani
doaj +1 more source
Behaviour of pultruded beam-to-column joints using steel web cleats [PDF]
, 2013 Response of pultruded Fibre Reinforced Polymer (FRP) beam-to-column joints with steel bolted web cleats is studied through physical testing. Two joint configurations are considered with either three or two bolts per cleat leg, as per drawings in a ...
Qureshi, Jawed, Mottram, J. Toby
core +1 more source
Prediction of Joint Shear Deformation Index of RC Beam–Column Joints
Buildings, 2020 In the analysis of reinforced concrete (RC) buildings, beam–column joints are regarded as rigid nodes. In fact, joint deformation may make a significant difference in the lateral response of RC buildings if joints are not properly designed and detailed ...
Dagvabazar Gombosuren, Takeshi Maki
doaj +1 more source
Three-dimensional analysis of reinforced concrete beam-column structures in fire [PDF]
, 2009 This is the author's accepted manuscript. The final published article is available from the link below. Published version copyright @ 2009 ASCE.In this paper a robust nonlinear finite-element procedure is developed for three-dimensional modeling of ...
Plank, RJ, Huang, Z, Burgess, IW
core +1 more source