Results 61 to 70 of about 1,344,359 (296)

Manufacturing of Porous Glass by Femtosecond Laser Welding

Micromachines, 2022
Based on femtosecond laser glass welding, four different porous structures of welding spots were formed by the manufacturing processes of spatiotemporal beam shaping and alternating high repetition rate transformation.
Hua Tan, Jiahui Pan, Xiaojia Zheng, Xiaoquan Fu, Yuxun Zhang, Yanxing Liu, Qiheng Huang   +6 more
doaj   +1 more source

Purification and preparation of Marchantia polymorpha Auxin Response Factor 2 for phase separation studies

FEBS Open Bio, EarlyView.
We describe detailed protocols for the purification and preparation of Marchantia polymorpha Auxin Response Factor 2 (MpARF2). This protein is fused to an MBP solubility tag and an mNG fluorescent tag and is purified from Escherichia coli. The presented procedures make it possible to study MpARF2 assemblies, which could arise from phase separation ...
Bas Janssen, Robin Romein, Willy A. M. van den Berg, Simon Lindhoud, Jan Willem Borst, Carlo P. M. van Mierlo   +5 more
wiley   +1 more source

Comparative assessment of crystallographic and cryo‐EM models in the Protein Data Bank

FEBS Open Bio, EarlyView.
Raw data obtained by X‐ray crystallography or cryo‐EM result in experimental maps, ultimately fitted by atomic models. Although the physical principles are different, the final results can be viewed, compared, and evaluated in the same way. With cryogenic electron microscopy (cryo‐EM) on track to surpass X‐ray crystallography as the preferred method ...
Alexander Wlodawer, Pawel Rubach, Zbigniew Dauter, Wojciech Dec, Dariusz Brzezinski, Marta Kulik, Wladek Minor, Mariusz Jaskolski   +7 more
wiley   +1 more source

Using fluorescence fluctuation spectroscopy to quantify molecular dynamics within cells

FEBS Open Bio, EarlyView.
Microscopy techniques like fluorescence correlation spectroscopy (FCS) and number and brightness analysis (N&B) allow to quantify concentrations, diffusion rates, and oligomerization of fluorescently labeled molecules in the living cell. In this protocol the principles of how to set up these types of experiments are described including calibration ...
Mark A. Hink
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Topological beaming of light: proof-of-concept experiment

Light: Science & Applications
Beam shaping in nanophotonic systems remains a challenge due to the reliance on complex heuristic optimization procedures. In this work, we experimentally demonstrate a novel approach to topological beam shaping using Jackiw-Rebbi states in metasurfaces.
Yu Sung Choi, Ki Young Lee, Soo-Chan An, Minchul Jang, Youngjae Kim, Seungjin Yoon, Seung Han Shin, Jae Woong Yoon   +7 more
doaj   +1 more source

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

Advanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba, Sang‐Hyeok Lee, Christina Gasper, Martina Freund, Sandra Korte‐Kerzel, Ulrich Kerzel   +5 more
wiley   +1 more source

Crack-free manufacture of single weld tracks on aluminum alloy 6013 with the usage of laser beam shaping and oscillation strategies

Journal of Advanced Joining Processes
The present paper investigates the application of laser beam shaping and laser beam oscillations (wobbling) for laser processing of the crack-prone aluminum alloy 6013, used in automotive and aerospace applications.
Thomas Stoll, Maximilian Schmitt, Laura-Marie Müller, Frank Palm   +3 more
doaj   +1 more source

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

Advanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour, Prithwish Tarafder, Anton Wiberg, Huanyu Li, Johan Moverare, Patrick Lambrix   +5 more
wiley   +1 more source