Results 121 to 130 of about 5,384,913 (273)

PERBANDINGAN KUALITAS MATERIAL BEARING MERK SKF, FMB, NKK, DAN JAL TERHADAP TERHADAP SIFAT FISIS DAN MEKANIS

Media Mesin, 2017
ABSTRAK   Penelitian ini bertujuan untuk mengetahui kualitas bahan yang digunakan pada empat merk bearing (SKF, FMB, NKK, dan JAL) berdasarkan data-data pengujian sifat- sifat mekanik serta struktur intern (struktur mikro) pada benda uji tersebut dan ...
Masyrukan Masyrukan, Ngafwan Ngafwan, Taufik Surya Nugroho   +2 more
doaj  

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

CFD Investigation of Influences of Reverse Textures on Bearing Surface of a Journal Bearing

Journal of Applied Fluid Mechanics, 2014
It has always been the subject of interest and research to find out most efficient method to minimize the frictional loss of any mating surface in any mechanism. But it has been identified that only improvement of lubricating material cannot help much.
Santosh Kumar Mishra, Sahu Shatendra, Arnab Choudhury   +2 more
doaj  

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Class prototype rectification and multi-scale feature measurement for few-shot classification of bearing surface defects. [PDF]

Sci Rep
Cang Y, Li C, Zhang X, Ma J, Zhou Z.
europepmc   +1 more source

A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle, Cesar Alvarez‐Llamas, Vincent Motto‐Ros, Christophe Dujardin, Jérémie Margueritat, David Rodney   +5 more
wiley   +1 more source

The Effect of Bearing Surface On the Survival of Cementless and Hybrid Total Hip Arthroplasty: An Analysis of Linked National Joint Registry and Hospital Episode Statistics Data. [PDF]

JB JS Open Access
Davis ET, Raikou M, McGuire AJ, Pagkalos J.   +3 more
europepmc   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Small target detection of bearing surface defects based on improved YOLOv5s. [PDF]

PLoS One
Xu H, Shi X, Zhang H, Yang F, Chen Y.
europepmc   +1 more source