Results 111 to 120 of about 1,346,084 (256)
Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam
Advanced Engineering Materials, EarlyView.Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Effect of Distributed Superficial-Velocity in Deep-Bed Grain Drying [PDF]
, 2000 This paper deals with influence of velocity field distribution to heat and mass transfer process in deep bed grain dryers. Two-dimensional (2D) models of deep-bed grain dryers were built by considering simultaneously momentum, heat, and mass transfer in ...
Istadi, I., Sitompul, J.P
core
Information on the houses in which bed net interventions were conducted.
, 2014 a)A, adults (age>15 years); C, children (age ≤15 years).Information on the houses in which bed net interventions were conducted.
Hitoshi Kawada (344540) +7 more
core +1 more source
How important is the angle of tilt in the WHO cone bioassay? [PDF]
, 2016 The World Health Organization (WHO) cone bioassay plays an integral role in the evaluation of the efficacy of long-lasting insecticidal nets as well as insecticides used in indoor residual spraying.
Müller, Pie +5 more
core +1 more source
Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses
Advanced Engineering Materials, EarlyView.Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk +4 more
wiley +1 more source
Hydrodynamic and solid residence time distribution in a circulating fluidized bed: experimental and 3D computational study [PDF]
, 2008 Vertical profiles of local pressure, horizontal profiles of net vertical solid mass flux, and residence time distributions (RTD) of the solid phase are experimentally assessed in the riser of a small scale cold Circulating Fluidized Bed of 9 m high ...
Simonin, Olivier +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley +1 more source
The influence of multiple tubes on the tube-to-bed heat transfer in a fluidised bed [PDF]
, 2010 There have been few studies modelling both flow and heat transfer in fluidised beds. The kinetic theory of granular flow (KTGF) has been used for flow prediction in the past without heat transfer modelling.
Gu, S. +8 more
core +1 more source
Household bed net ownership and use among under-5 children in Nigeria
Research and Reports in Tropical Medicine, 2013 D Chidiebere Osuorah,1,2 Chijioke Elias Ezeudu,2 Stanley Kenechi Onah,2 Obinna Tochukwu Anyabolu31Child Survival Unit, Medical Research Council UK, The Gambia Unit, Banjul, The Gambia; 2Department of Pediatrics, Nnamdi Azikiwe University Teaching ...
Osuorah DC +3 more
doaj
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source