Results 111 to 120 of about 10,977 (167)

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Additive Manufacturing of Patient‐Specific Intracranial Aneurysm Cell Culture Models

Advanced Materials Technologies, EarlyView.
Patient‐specific intracranial aneurysm models were fabricated using chocolate moulding, 3D printed water‐soluble cores, and direct resin 3D printing. Moulding PDMS around sacrificial cores made of chocolate or 3D printed water‐soluble resin yielded accurate, expandable, and endothelializable models that outperformed resin‐based approaches.
Chloe M. de Nys, Jaimee‐Lee Wood, James I. Novak, Danilo Carluccio, Craig D. Winter, Ashley R. Murphy, Mark C. Allenby   +6 more
wiley   +1 more source

Shaping Carbon Nitrides for Advanced Macrostructures

Advanced Materials Technologies, EarlyView.
This review examines how carbon nitride can be shaped through a range of printing and interfacial assembly methods. By bringing together additive manufacturing and liquid–liquid structuring concepts, carbon nitride is moving beyond its traditional powder‐based photocatalyst form toward digitally designed robust macroscale architectures with high design
Simona Baluchová, Baris Kumru
wiley   +1 more source

Three‐Dimensional Printed Microarchitected Hierarchically Porous Biodegradable PLA/S/CNT Nanocomposite Electrodes for High‐Performance Lithium–Sulfur Batteries

Advanced Materials Technologies, EarlyView.
Hierarchically microarchitected PLA/S/CNT cathodes are fabricated via scalable fused filament 3D printing as high‐sulfur‐loading hosts for rechargeable lithium–sulfur batteries. The assembled Li–S cells with sulfur loadings up to 17 mg cm−2 deliver an areal capacity of 9.2 mAh cm−2 and retain 96% of their discharge capacity after 100 charge–discharge ...
Vinay Gupta, Pawan Verma, Fahad Alam, Krishnaiahnahundi Manjunathaswamy Mohan, Shanumgam Kumar   +4 more
wiley   +1 more source

Lithostratigraphy of Bagh Beds and its correlation with Lameta Beds

Journal of the Palaeontological Society of India, 1981
S. K. Singh, H. K. Srivastava
doaj   +1 more source

Fully 3D‐Printed Wave‐Wound Electromagnetic Motors

Advanced Materials Technologies, EarlyView.
This work presents the first fully 3D‐printed wave‐wound electromagnetic motors, which are created using conductive nanoparticle inks, carbon‐filled nylon polymers, and surface mount components. These motors can achieve a stall torque of 7.62N·mmA−1$7.62 \nobreakspace N{\cdot }mm A^{-1}$ and efficiency of 28.2 %, which approaches the performance of ...
Joseph Schwalbe, Sebastian Mettes, Eduardo Francke, Kenneth W. Allen, Yi Chen Mazumdar   +4 more
wiley   +1 more source

Magnetic Droplet Manipulation on Open Surfaces

Advanced Materials Technologies, EarlyView.
Recent advances in the manipulation of magnetic droplets demonstrate various manipulations on open surfaces, including transport, splitting, merging, and force‐controlled motion, enabled by magnetic particles and external fields. ABSTRACT Manipulation of liquids on a smaller scale enables applications in various fields, particularly diagnostics and ...
Robab Jahangir, Vahid Nasirimarekani
wiley   +1 more source

Bamboo Medical Application: A State‐of‐the‐Art Review

Advanced Materials Technologies, EarlyView.
This review presents a structured classification of bamboo's current use in healthcare. It organizes applications into medical textiles and medical devices, with further divisions based on function and level of invasiveness. It also examines material utilization based on bamboo's structural role, highlighting how it supports both protective and ...
Haymanot Beza Lamesgin, Koosje van der Stoel, Vera Popovich, Paul Breedveld   +3 more
wiley   +1 more source