Results 111 to 120 of about 9,181 (289)
Temperature-dependent elastic shear modulus of a saturated lateritic clay [PDF]
E3S Web of ConferencesThe thermo-mechanical behaviour of saturated clays and sands has been studied by many researchers, considering that it is useful in many geotechnical problems, such as the analysis of energy foundations and the effects of climate change on earth ...
Bentil Obed Takyi +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study reports the development of antibacterial ceramic scaffolds derived from natural bovine bone. The bones were processed through sequential boiling and hydrogen peroxide treatment to remove organic matter, producing porous, mineral‐rich scaffolds.
Mohamad Hassan Taherian +6 more
wiley +1 more source
Utilização de bender elements na determinação do módulo de distorção
, 2013 Este trabalho apresenta a utilização de bender elements na determinação do módulo de distorção de uma areia. A amostra foi preparada para um determinado índice de vazios e ensaiada à compressão isotrópica até 400 kPa.
Pereira, Cláudio Luís Barros Batista +3 more
core
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Characterization of Loire river sand in the small strain domain using new bender-extender elements
, 2003 International audienceNew piezo-ceramics transducers called bender-extender elements are used to characterize the mechanical behavior of the alluvial Loire River sand in the small strain domain.
Dano, Christophe +2 more
core
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Análisis de señales de Bender Elements durante el ensayo triaxial [PDF]
, 2015 RESUMEN: Este artículo presenta y discute tres métodos para evaluar la velocidad de la onda cortante, Vs, con base en el análisis de señales de “Bender Elements” (BE) tomadas durante ensayos triaxiales. Los métodos de tiempo de viaje de pico-a-pico (peak-
Zapata Medina, David Guillermo +1 more
core
Advanced Engineering Materials, EarlyView.Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon +3 more
wiley +1 more source
Shear wave velocity measurements of normally consolidated kaolinite using bender elements
, 2005 The stiffness of ultra-soft clay can be an important parameter in test beds used to study and develop design procedures for offshore foundations. Shear wave velocities were measured in such a test bed of kaolinite slurry from the initial stages of ...
Jung, Min Jae
core +1 more source
From Shear to Sound: Mechanics–Acoustics Mapping of TPMS Lattices
Advanced Engineering Materials, EarlyView.Triply periodic minimal surface (TPMS) lattices are mapped across mechanical and acoustic performance, revealing that descriptors validated in compression fail under shear. First‐time comparison with trusses included. A transition from porous to resonance‐driven absorption emerges at 25% density.
Lucía Doyle +3 more
wiley +1 more source