Results 231 to 240 of about 1,161,291 (313)
Some of the next articles are maybe not open access.
, 2021
The adhesive joints used in airframe and wing sections of aircrafts are generally subject to dynamic (fatigue) loading rather than static loading due to environmental conditions. The dynamic loading formed on wing sections of aircraft is generally in the
Salih Akpınar, Resul Sahin
semanticscholar +1 more source
The adhesive joints used in airframe and wing sections of aircrafts are generally subject to dynamic (fatigue) loading rather than static loading due to environmental conditions. The dynamic loading formed on wing sections of aircraft is generally in the
Salih Akpınar, Resul Sahin
semanticscholar +1 more source
Ultra-high three-point bending fatigue performance of nano-silica-reinforced CFRP
, 2021The effect of silica nano-particles on the three-point bending fatigue characteristics of plain weave carbon fiber composites (CFRP) was analyzed in the VHCF regime.
Junliang Ding, Li Cheng
semanticscholar +1 more source
Volume 11: 2023 International Power Transmission and Gearing Conference (PTG), 2023
Abstract Gears in vertical lift applications will typically experience greater than 107 bending fatigue cycles over their design lifetime. Currently, fatigue life prediction of gears exceeding 107 cycles are based on empirical correlations, since collection of fatigue data beyond 107 cycles is impractical with traditional fatigue testing
Zachary A. Cameron, Thomas Tallerico
openaire +1 more source
Abstract Gears in vertical lift applications will typically experience greater than 107 bending fatigue cycles over their design lifetime. Currently, fatigue life prediction of gears exceeding 107 cycles are based on empirical correlations, since collection of fatigue data beyond 107 cycles is impractical with traditional fatigue testing
Zachary A. Cameron, Thomas Tallerico
openaire +1 more source
, 2020
Gear bending fatigue life is a primary consideration in gear design. Each gear tooth is subjected to cyclic root stresses that may cause fatigue fracture. A gear in a transmission is subjected to either fully released or fully reversed loading conditions,
I. Hong, A. Kahraman, N. Anderson
semanticscholar +1 more source
Gear bending fatigue life is a primary consideration in gear design. Each gear tooth is subjected to cyclic root stresses that may cause fatigue fracture. A gear in a transmission is subjected to either fully released or fully reversed loading conditions,
I. Hong, A. Kahraman, N. Anderson
semanticscholar +1 more source
, 2020
Bending fatigue is one of the most common failure modes in spur gears. In carburized spur gears, subsurface failure initiation is characteristic for the high cycle fatigue regime, which is rather hard to detect and may cause rapid crack growth and ...
I. Čular +3 more
semanticscholar +1 more source
Bending fatigue is one of the most common failure modes in spur gears. In carburized spur gears, subsurface failure initiation is characteristic for the high cycle fatigue regime, which is rather hard to detect and may cause rapid crack growth and ...
I. Čular +3 more
semanticscholar +1 more source
, 2021
As bonded components of many industrial structures are inevitably under bending fatigue loads, it is essential to improve their mechanical behavior under these loads.
P. Zamani +2 more
semanticscholar +1 more source
As bonded components of many industrial structures are inevitably under bending fatigue loads, it is essential to improve their mechanical behavior under these loads.
P. Zamani +2 more
semanticscholar +1 more source
Bending Fatigue of Cable Stays
Journal of Bridge Engineering, 2001Large amplitude stay-cable vibrations have been observed numerous times in the past few years in two long-span cable-stayed bridges in Texas: the Veterans Memorial Bridge near Port Arthur and the Fred Hartman Bridge near Baytown. In most cases, these vibrations have occurred in combination with light rain and relatively low winds.
J. Dowd +4 more
openaire +1 more source
, 2020
The 7075-aluminum alloy is often used in aerospace, automotive, and maritime sectors owing to its high strength-to-weight ratio. Application of Physical Vapor Deposition (PVD) coating has proved to increase tribological properties and corrosion ...
S. Baragetti, Ž. Božić, E. V. Arcieri
semanticscholar +1 more source
The 7075-aluminum alloy is often used in aerospace, automotive, and maritime sectors owing to its high strength-to-weight ratio. Application of Physical Vapor Deposition (PVD) coating has proved to increase tribological properties and corrosion ...
S. Baragetti, Ž. Božić, E. V. Arcieri
semanticscholar +1 more source
Bending fatigue characteristics of artificial knee ligaments
Journal of Biomechanics, 1987Knee joint motion is governed by the tibia and femur condyle surfaces, menisci and the ligaments. Instability of the knee joint is a continuing problem to the Physician treating knee injuries and is often accompanied by the damage to the knee liagments.
A. H. Soni +3 more
openaire +1 more source
Metal magnetic memory inspection of Q345B steel beam in four point bending fatigue test
, 2020The metal magnetic memory (MMM) method is a nondestructive testing method to inspect the early damage of steel structures. A four-point bending fatigue beam was inspected by this method during the whole fatigue life. The self-magnetic-leakage field (SMLF)
Xuran Zhao +3 more
semanticscholar +1 more source