Results 71 to 80 of about 98,725 (314)
Jixie chuandong, 2011 With the development of lightweight gear,the requirements of bending fatigue strength of gear teeth are increasingly high.Combined with the equation of tooth profile and the ANSYS Parametric Design Language（APDL）,the parameterization finite element model
何晓华, 陈兵奎
doaj
Experimental investigation of concrete fatigue resistance [PDF]
, 2014 A lack of knowledge on the fatigue resistance of self-compacting concrete (SCC) structures has led to the research presented in this paper. Several reinforced concrete beams were subjected to both static and cyclic four-point bending tests in order to ...
Boel, Veerle +3 more
core
Static strength and rotating bending fatigue strength of aluminum-lithium alloys.
Journal of the Society of Materials Science, Japan, 1990 Tensile properties and fatigue strength under rotating bending were investigated on two aluminum-lithium alloys, 2090 and 8090, and the results were compared with conventional aluminum alloys, 2024-T4 and 7075-T6511.The proof stress and tensile strength of Al-Li alloys were approximately the same as those of 2024 alloy, but were lower than those of ...
Keiro TOKAJI, Takeshi OGAWA, Yozo KATO
openaire +2 more sources
Smart Catheters for Diagnosis, Monitoring, and Therapy
Advanced Healthcare Materials, EarlyView.This study presents a comprehensive review of smart catheters, an emerging class of medical devices that integrate embedded sensors, robotics, and communication systems, offering increased functionality and complexity to enable real‐time health monitoring, diagnostics, and treatment. Abstract This review explores smart catheters as an emerging class of
Azra Yaprak Tarman +12 more
wiley +1 more source
Flex Fatigue Behavior Of Plastic Optical Fibers With Low Bending Cycles
AUTEX Research Journal, 2015 Flex fatigue behaviour of plastic optical fibres (POFs) with the diameters of 0.2 and 0.3 mm under different pretensions is measured with fatigue life curve by flexometer.
Huang Juan +2 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2015 Pure bending fatigue tests were conducted with single-sided fillet welded T-joint specimens. Two load conditions, which were given the tensile and compressive stresses in the weld toe, were applied, and fatigue strengths at 2×106 cycles were determined ...
Yasuki KITA +2 more
doaj +1 more source
Proposed design procedure for transmission shafting under fatigue loading [PDF]
A new standard for the design of transmission shafting is reported. Computed was the diameter of rotating solid steel shafts under combined cyclic bending and steady torsion is presented.
Loewenthal, S. H.
core +1 more source
Experimental analysis of manufacturing parameters’ effect on the flexural properties of wood-PLA composite parts built through FFF [PDF]
, 2020 This paper aims to determine the flexural stiffness and strength of a composite made of a polylactic acid reinforced with wood particles, named commercially as Timberfill, manufactured through fused filament fabrication (FFF).
Jerez Mesa, Ramón +4 more
core +2 more sources
Probabilistic Estimation of Fatigue Strength for Axial and Bending Loading in High-Cycle Fatigue
Materials, 2020 In this paper, the sensitivity to the type of loads (axial and bending loading) of selected construction materials (AW6063 T6 aluminum alloy, S355J2+C structural steel, and 1.4301 acid-resistant steel) in high-cycle fatigue was verified. The obtained S-N fatigue characteristics were described by a probabilistic model of the 3-parameters Weibull ...
Tomasz Tomaszewski +3 more
openaire +2 more sources
Advanced Healthcare Materials, EarlyView.Percutaneous prosthetic venous valves are fabricated by embedding stents in an electrospun matrix that extends luminally to form leaflets. The design shields leaflets from hyperplastic cells, isolates struts from blood contact, and avoids discrete anchoring points.
Dario Arcuti +6 more
wiley +1 more source