Results 81 to 90 of about 113,140 (299)
Scientific Reports, 2021 Mm-wave dielectric waveguides are a promising and low-cost technology for the transmission of ultra-high data rates. Besides the attenuation (losses) and group delay, the bending loss of the dielectric waveguides is also one of the key parameters to ...
Thanh-Luan Vu +5 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Design of all-solid leakage channel fibers with large mode area and low bending loss [PDF]
, 2009 We investigate a novel design for all-solid large mode area (LMA) leakage channel fibers (LCFs) for high-power Yb-doped fiber lasers and amplifiers, based on a single down-doped-silica rod ring surrounding a seven-cell pure-silica core, aiming for ...
Lorenzo Rosa (4053517) +10 more
core +2 more sources
Low-DMGD, Large-Effective-Area and Low-Bending-Loss 12-LP-Mode Fiber for Mode-Division-Multiplexing
IEEE Photonics Journal, 2019 We report the design of 12-LP-mode (21-spatial-mode) fiber with a low differential mode group delay (DMGD), a large effective area, and a low bending loss that is adapted to a mode-division-multiplexing system over the C+L band.
Huan Zhang +4 more
doaj +1 more source
Multiple-cladding fibers with reduced bend loss
Journal of the Optical Society of America A, 2007 We demonstrate that a highly bend-resistant fiber can be realized. It is shown theoretically that, by introducing both depressed and elevated rings into the cladding, bending loss can be reduced significantly. A fiber based on this design has been fabricated and characterized as a first step toward achieving this goal.
Tomljenovic-Hanic, Snjezana +4 more
openaire +3 more sources
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study reports the development of antibacterial ceramic scaffolds derived from natural bovine bone. The bones were processed through sequential boiling and hydrogen peroxide treatment to remove organic matter, producing porous, mineral‐rich scaffolds.
Mohamad Hassan Taherian +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley +1 more source
Mechanical Engineering Journal, 2018 Three silicon-nitride (Si3N4) ceramic specimens (differing in terms of sintering additive and bending strength) were corroded and tested in 3-mol/L-HCl aqueous solutions at 80°C for 1500 h.
Masatsugu ARAI
doaj +1 more source
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source